Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I am using a 802.11a card on my laptop and it is running XP OS. For some reason after restarting and logging into the machine I have to reinsert the card to get the signal. My machine is set to start the "Network Connections" service automatically.Th...
I would like to know if the usage of "LEAP + MAC address authnetification + broadcast key rotation or TKIP" is sufficient to provide the minimum of security in wireless areas.If yes the key rotation must be managed by which components : Radius server...
Hi,Does anyone know if Cisco has incorporating WPA support to the Aironet Products ? If so, where can I find details on which products ?Any info would be appreciated.Best Regards,Armand
AP 1200 doesnot boot up. When I tried to boot it up, it gives the following error: "The system unable to boot automatically because there are no bootable files to boot." Than it displays the software version of the AP and Cisco contact info. After di...
Hello,Sounds simple, but when you specify right or left in the setup, is it facing the the front of the box, with the logo? Or as you look at the back of the AP?And to further confuse the issue, which is right and left on the internal card? Looking a...
Hi All,I use Cisco Aironet 350 series to provide point to point connection of about 15 KM distance. The configuration is as follows:CSAC Ver 3.0---HUB ----|---RootBridge(SSID 1) |---Non-Root (SSID 2)----Root (SSID 2)---|-HUB RootX(SSID1)--|RootBridge...
Hi All,I use Cisco Aironet 350 Series bridges to connect buildings in my organisation. Within the buildings I have some users on wired LAN using network cards, while others are on wireless using cisco PCI cards. While the wireless users can be authen...
HiDoes the news version of BBSM 5.2 supports IOS APs? I cant find any infos on cco.thxregards Bernhard
[issue 1] How many video codec servers can be operating with one 1200? Please let us know. In my case, the manimum mumber of video codec was 2. Each video condec server has 800kbps and the total throughput is calculated to 1.6Mbps. When I was adding ...
Has anyone implemented a GPRS solution using a PIX? If so, did you encounter any problems? Basically I'm looking into implementing a GPRS solution for a customer, i.e. I'll allow GPRS traffic out (smtp only) by using ACL on the inside interface via p...
Hi, i had a thread on the same topic before.....somehow the problem went away, i was able to enable 128 bit ( and USE IT ) on both ViewSonic AirPanel 150 and 1200. But something happened and i cannot use wep anymore.Works fine when i set all keys to ...
A client has a AP350 - my goal is to have it be open (so that visitors could use their WLAN to connect to their own company sites, email, surf) so what I was hoping to accomplish was something like this.Setup the AP350 with an external static IP addr...
Hello allI would like to ask what is the number of devices that an aironet can support, especially for 802.11b, either theoretical limitation or/and practical..Thanx alot!
Hi,I have tried operating my notebook with both a Cisco Aironet wireless LAN adapter and my fastethernet port active.By doing a trace-route, I notice that my data is sometimes transmitted via my wireless LAN adapter, and sometimes via my NIC.I initia...
The AP display this message as I "boot" up to the main menu.Motherboard: MPC860 50MHz, 2048KB FLASH, 16384KB DRAM, Revision 21Bootstrap Ver. 1.01: FLASH, CRC AB31F5C0 (OK)Initialization: Improper Motherboard ConfigWhat can I do to recover the AP
