Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hello,I'm faced with installing a WLAN between two buildings. They're about 2 KM a part. I think I have line of sight between the two, but is there any way to be absolutely sure. I'm wondering if I purchased one of those little laser thingies if that...

dwalsh by • Level 4
  • 921 Views
  • 1 replies
  • 0 Helpful votes

Hi,Is is possible to use Windows IAS Service (Windows 2000) for MAC-Based-Authentication of Wireless Clients ? The AP is Cisco 1200.On the same note, can IAS be used for PEAP Authentication ?Do i need to install some ServicePacks for this ?Regards\\ ...

mnlatif by • Level 7
  • 949 Views
  • 2 replies
  • 0 Helpful votes

I have installed an AP1200 with an IP obtained through DHCP reservation (MAC address). I have a linux DHCP server serving 30 IP addresses in the same network where the AP is connected. I am doing some tests with a PC WinXP SP1 wireless client (using ...

ramada by • Community Member
  • 652 Views
  • 1 replies
  • 0 Helpful votes

I want to autenticate admin users in a AP350 with v12.01T1, with a tacacs+ server (ACS v3.1).I configured on the AP350 an authentication server, port 49, tacacs, correct key, etc.I configured the aaa client, users, etc, and I obtain in the ACS "faile...

Here's a specific example, I gather this information via the web interface by going to the Associations table, then click the MAC address/link of a connected client:MAC: 00:04:5a:ef:bf:70To Station:Total Bytes OK:4963928How what is the OID for that v...

kmleon by • Level 2
  • 3363 Views
  • 13 replies
  • 0 Helpful votes

Greetings,I would like to find out how can I reduce the time take for the LEAP client to look for the Domain Controller over WAN? Is there something we need to configure on the AP or on the router?I am using a leased line from my remote site to my ce...

skkwok by • Community Member
  • 1431 Views
  • 5 replies
  • 0 Helpful votes

Hi, Can someone explain why the defaultf timeouts for devices in the association tables seem to be so long (to me anyway)? Or point me to docs that explain why these are set this way.....I've not had much luck looking myself.....thanks in advance.......

jimbostan by • Level 2
  • 701 Views
  • 2 replies
  • 0 Helpful votes

I am interested in replacing the integrated wireless card in a dell notebook with a Cisco card so I can utilize LEAP. Is this an option? What does the process entail? How many have done this? Is it Cisco supported?thanks,Dan Laden

dladen by • Level 3
  • 578 Views
  • 1 replies
  • 0 Helpful votes

I downloaded the newly released Windows Intall Wizard bundled with the latest ACU(6.0), Driver(3.5),Firmware(5.02.19), ACM(2.0).It installed properly and all worked well, and I like the ACM. However, the new ACU 6.0 caused a conflict with the Windows...

khs8 by • Community Member
  • 968 Views
  • 4 replies
  • 0 Helpful votes

Received NULL MAC address as DESTINATION from source [ax340]000103e2f6ac on port "fec0"My Aironet LOGS are full of messages of this kind but everything seems to work fine. I do not exectly understand what do they mean (null mac destination address ?!...

admin_2 by • Level 7
  • 549 Views
  • 1 replies
  • 0 Helpful votes

I've been trying to figure out the need for configuring the radio on a 350 AP with a unique IP other than it's ethernet IP? Doc says it's required for Standby mode or advanced configurations. Anyone have examples? Just don't see it.J.

j.fanizzi by • Community Member
  • 644 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card