Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I have a 2 340 ap's. I have 2 340 pcmcia cards. One of the cards I have has been sent back 3 times because of bad quality on card. I got new one and it has same problem. So I put in other 340 pcmcia card and signal and quality are excellent. So then ...

terry by • Community Member
  • 1772 Views
  • 5 replies
  • 0 Helpful votes

We have installed several Aironet 340 wireless bridges on different campuses. These bridges clearly offer a great value in replacing low speed serial links. Has anyone used FEC or MultiLink to aggregate multiple bridge links successfully? I tried FEC...

abrahamj by • Community Member
  • 3194 Views
  • 8 replies
  • 0 Helpful votes

My network is spread over two remote buildings and the distance between them is nearly 800m.I want to connect the Lan of both building by Aironet 340.Each building have 80 nodes or in future it would be expended.Now I need a solution and physical net...

Hi all,anyone have any experience with trouble dialing into a cisco 3640??we have currently just bought a siemens laptop that will not dial into the router with error message 678 "no answer" - however we have other laptops that dial in fine and they ...

redmayne by • Community Member
  • 1114 Views
  • 1 replies
  • 0 Helpful votes

AllNeed help!I have a client that needs Symbol Netvision integration with CCM 3.0(9).I hv tried to look thru the CCO but no concrete solution .Do anyone in the forum can help me in this integration.What should I configure in CCM and the gateway.I am ...

uttaran by • Community Member
  • 1147 Views
  • 1 replies
  • 0 Helpful votes

Are there any good configuration examples for a large mobile ip network?

felecia by • Community Member
  • 1448 Views
  • 2 replies
  • 0 Helpful votes

I have tested the ACU utility for the Access Point 340 cisco, works ok with the PCMcia card, the LSM (Link Status Meter) works fine.I need the same tool for test the link between two aironet Cisco Bridges 340. Can tell me please if that tool exist?.t...

evolutionet by • Community Member
  • 1307 Views
  • 2 replies
  • 0 Helpful votes

I have 3 locations A, B, and C. Out of which A is my Server location and does not have LOS with C. While B has LOS with both A and C. How can I use 350 bridges to overcome the problem at location B ?

1.When the bridge AIR - BR352 (350 series) will be on sale?2.Is it possible to know previously its cost (approximately)?In GPL its cost is not specified. Thanks in advance for any replay.

asvir by • Community Member
  • 1001 Views
  • 1 replies
  • 0 Helpful votes

I have a customer looking to deploy a WLAN. His users are distributed over 3 VLANs. He would like to have his users be able to roam throughout the WLAN, and still retain their VLAN assignments.We thought we could do this via dynamic VLAN ports, but s...

Just trying to see what kinds of ditances people are using these links at, as well as how high they have placed their antennas in order to achieve that distance? I think a small discrition of the equipment used would be helpful as well. We could use ...

jcomca by • Community Member
  • 2018 Views
  • 4 replies
  • 0 Helpful votes

Hello,I am running BGP on my Cisco7204 router. I have a network of 8292 nodes. the gateway for all my nodes is the router mentioned above. I connect to an ISP with another AS. I too have an AS number. I want the request send by nodes in my network as...

Review Cisco Networking for a $25 gift card