Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Operational status is showing down as well as no SSID's are broadcasting. Access point is already joined with controller, the DHCP IP which is getting this AP is also pingable. Cisco Catalyst 9800-L Series WLC, I am using to connect this access point...
Catalyst wlc 9800 running 17.3.6 code (last that supports the 2702I) I have a WLAN SSID profile that if applied to a 2702I will allow old intermec ck3 handhelds running Windows Embedded Handheld 6.5 Classic CE OS 52.29354 (Build2935415i3, 12143). ht...
Dear Experts Community,I need you advice on the designWe have 2 x 9800 WLCs working in SSO mode with 400 WAPs and all SSIDs are configured with centrally switched mode.We have 1 LAG connected to Core Switches on trunk port for corporate data and voic...
Hello Cisco Community,Is it possible de configure the "C9120AXI-EWC-E" as a ROOT-AP (RAP / Mesh controler) ? My previous configuration was :2 AP1231 (Aronet 1200 series) linked together in WORKGROUP BRIDGE Mode >N°1 was a AP1231 in "WGB root with...
Hardware:WLC 9800-CL on Hyper-V - 17.9.3 Cuppertinoc9210i API'm trying to setup an SSID with WPA3 Personal security only but I'm running into a weird issue with both Windows 10 and Windows 11 (My Pixel5 doesn't seem to care)If I configure the SSID wi...
Buenas tardes,Tengo una Mesh con AP IW-6300 con 2 controladoras C9800 por HA (Conectadas con el puerto RP entre si)Aguardo que las WLC esten sincronizadas (una como Active y Standby). Entonces procedo a apagar la activa, toma el control la Stanby, pe...
Hi,We use a guest concentrator to tunnel our Guest SSID traffic back to the DC from WAN sites. The Guest SSID uses ISE radius and ISE sign on page (sponsored portal). Recently we have noticed we have to reload the Meraki access points for users to se...
Hello,I have 3 CBW 150AX, all run fine.However, when I log in to the Primary AP dashboard, I do not see the list of APs under Monitoring->Network Summary->Access Points.The following describes the situation:When I go to Monitoring->Network Summary, I...
Resolved! Local Auth issues with Android devices
Hi Guys,I am trying to get Meraki local authentication working for Wi-Fi device with eap-tls authentication.Current topology:- Azure AD joined windows and android devices (dedicated).- SCEP certs deployed to clients.- Root cert uploaded to meraki wif...
Resolved! Problem with Local Authentication
Hi,We are trying to get Local Authentication to work on a MR33 access-point with latest firmware.We already checked message:https://community.meraki.com/t5/Wireless-LAN/Local-Auth-issues-with-Android-devices/m-p/196714Our infrastructure is as follows...
We have been using Meraki for years and all of a sudden last week Windows 10 clients weren't able to connect. Auth would succeed on the Windows NPS server but on the client side they would get a message saying "Cant connect to this network" or someth...
Good morning, Just checking in here to see if anyone would know a way to have the Meraki switches to auto detect when a new Meraki AP is connected and configure the port as a trunk with the proper vlans allowed. I heard from someone recently that thi...
Can a C9100 series AP running Embedded Wireless Controller firmware connect function as a lightweight AP under a separate controllerWe might be getting a few thousand Acces points that we would needed to factory reset so we can sell them along but to...
HelloWe plan to use Aeroscout Asset Tracking System for a big mall that use cisco wireless infrastructure (WLC 8540, AP 2802, MSE 3365 CMX10, Prime Infra 3.2). I have below questions and would appreciate any help.1- Can we integrate Aeroscout Systems...
Resolved! Cisco AP not registering with controller
Hello,I have configured a Cisco 2504 WLC in my home lab. I have a WLAN configured and connect the AP to the switch. The Cisco AP joins the controller, and I can see it, but it does not broadcast the SSID, and the AP blinks Blue, red, and Green.Cisco ...
