Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi c9800 wlc has guest ssid. Under the same WLC, we can see two guest State(Monitor---->Client) when user access the guest ssid. One is "Run" and second is "Web Auth Pending". What reason cause the second state? Thank you
Has anyone been able to configure WPA3 & 802.11r on the new MR 30.1 beta firmware?I have an MR46 & MR36H in a network running MR 30.1.Dashboard continuously rejects the config, saying "The current WPA encryption mode does not support dot11r."I've tri...
I have been receiving these error messages while I'm trying to join a LWAP to the WLC. I tried running the command config ap cert-expiry-ignore mic enable on the WLC, but it won't work.WLC software version is 7.6.100.0.AP model AIR-CAP3502I-E-K9AP im...
Hi, We are currently using WLC AIR-CT2504-5-K9. It has reached end of support in April 2023. Therefore, we hope to replace model C9800-L-C-K9 instead of AIR-CT2504-5-K9. Now we have connected the AP models AIR-AP1832I-E-K9C and AIR-CAP1702I-E-K9. do ...
Hi All, Running fabric in a box on with wireless enabled, on a stack of Cisco Catalyst 9300 Series Switches (C9300L-48UXG-4X / C9300L-24P-4X). Need to upgrade the WLC version from 17.3.4 to 17.6.4 - Can this be done on the WLC only or does the stack ...
Hi all,I'm trying to connect new APs to WLC at a new location and the APs are joining and seconds later they are disconnecting from the WLC. When I consoled into one of the APs it's showing the output I have attached, below is part of what I'm seeing...
Hello,I recently raised a ticket with meraki because I have a MR74 that seemed to be stuck on a low TX power (well below 20).They explained that its because the regulatory rules say the max power is 20 (or 23, somewhere around there) - and with the a...
Hi All, Running 9800-40 WLC's Version 17.6.4 and DNAC Version 2.3.3.6-70045, would like to utilise the new AP "ZONES" feature via DNAC. What version of WLC code is supported? Any docs/advise would be helpful. Cheers,
Dears,I have a cisco 1852i as master mobility express and i have bought cisco 2802i.can cisco 2802i join as subordinate AP under 1852i ??????
We are currently using the AIR-CT2504-5-K9 wireless LAN controller (WLC), which reached its end of support in April 2023. Consequently, we are looking to replace it with the C9800-L-C-K9 model instead of the AIR-CT2504-5-K9. Currently, we have deploy...
Hi All, Environment: WLC 5520 version 8.5.161.0. I have problem about Client connected SSID and It's can't obtain DHCP then this Wi-Fi status "no internet" Example: 2 SSID: A and B [WLAN config same interface VLAN Identifier 152] 1 SSID: C [WLAN conf...
Hello we have a C9800-CL and 9115 access points in flex mode. When we install wireless at a new site, we always need to wait for the first access point to download the firmware from the wlc at the data center and that takes time, because of the WAN l...
I have a scenario where we use ISE for EAP-TLS cert based authentication for wireless network. It has been working at our HQ for several months. Now we are trying to roll this out to our remote offices that connect to HQ over private WAN links.The is...
Hi ,Active WLC uplink goes down, when check the HA status we can see the below information, how to resolve this issue please suggest meWLC-9800-01#sh redundancy statesmy state = 13 -ACTIVEpeer state = 1 -DISABLEDMode = SimplexUnit = PrimaryUnit ID = ...
Has anyone had any issues with solarwinds and the amount of alerts it puts on AP's? I have had several alerts for AP's down for more than 15mins. However on the WLC for uptimes the AP's do not show any issues of that happening. There should be som...
