As shown in the attached capture, infinite redundancy iteration occurs as EHSA standby down during the redundancy process of 9800. The version is 17.9.4a. Do you know anyone?
Forum Posts
Bonjour,J'ai acquis 10 bornes AP 1832i pour harmoniser mon parc et avoir une gestion centralisée de ces bornes. 4 sont déjà en place et fonctionnent très bien, mais 4 des nouvelles bornes n'arrivent pas à se connecter à la console d'administration, c...
Resolved! DHCP on 5508 for APs
Hi all !I have a CISCO 5508 and i want to make a DHCP only for my AP not for client is it possible on this controler ?Actually my AP get network information from my DHCP server and i don't wan't to see my AP with my client on this same network.I don'...
Hello, I have had 3 of these APs (AIR-CAP3602I-E-K9) running for several years now and no issues. I have recently upgraded my broadband (1gpbs) and was hoping for faster speeds through the APs. I only get about 50mbps using 5GHz. I guess I need to up...
Hi All I'm debugging a EAP-TLS issue at the moment, between some iPads a WLC 8540 with 8.10.181.3 and 2800 APs. It works with 2700 AP models on this WLC, but nearly always fails with 2800 APs. I've now captured the radius communication between the WL...
Resolved! Roaming management
Hello everyone,My question is the following.In an environment with Cisco Lightweight APs (mix of 2802 and 9120) in Flexconnect mode under the supervision of a Cisco WLC (model 8540 with 8.10.183.0 version), who is in charge of roaming a client betwee...
This how my SSID is configured: c9800-1(config)#key config-key password-encrypt <key>c9800-1(config)#password encryption aes no broadcast-ssid security wpa psk set-key ascii 8 fHeEGWK[YCWF\PcLNgTidD]WQfGKVR[`aAAB no security wpa akm dot1x security...
HiLooking at radius accounting records details, in the case of records type "Interim-Update" I'm missing the attribute 46 (Acct-Session-Time). In AireOS WLC, all Interim-Update records includes that attribute, but with NX-OS only accounting records ...
Hi All,Recently my AP failed to join the controller (AIR-CT2504-K9) after I rebooted the controller. I tried to restored factory default to reconfigure them. But it is still failed to join the controller. I'm not able to identify the issue Sysinfo: (...
l get Error messenge of AP wil not join to vwlc l checked everthing is right but is wil not join still AP Model AO-2802I-B-K9 Error messenge ============================================================================================APCC16.7EDE.8D36#...
I am using: - Cisco AIRAP1572EACZK9 as root bridge with CISCO AIRONET AIR-ANT2547VG-N. - CISCO AIR -AP1262N-E-K9 as non-root bridge with an directional panel 5GHz I am trying to associate both of them but it seems that I can not and I do not understa...
Hello, I have 5508 WLC for around 5 years and managing Cisco AP's modeled 1832, 1831, 1815, 2600, 2700, and 2800 on my office 6 months ago we bought 10 units Cisco AP 9115ax and use EWC as the 9115ax controller, but we've recently bought WLC 9800 pla...
Dear All, I have C9115AXE AP which is running on firmware 17.13.0 and i want know that it is supported join on C2504 Hardware controller ( controller running on 8.3.150 version ) ? I also referred escalation matrix of wireless solution but not able t...
I'm in need of help with why my new 9th Gen iPads will not register to Meraki MDM solution, but older ones will.Did I miss something.Thanks
Resolved! Workgroup Bridges and DNA/SD-Access
Should wired clients connected to a workgroup bridge have any issues on a network using Cisco DNA and SD-Access? I'm just curious if identification of clients or applying an access policy to those clients behind the WGB would be a problem. A curren...
