The Field Notice FN70489 is affecting an IW3702 that I got for setting up a test lab. I can use CLI and make changes in the parameters and get it working but I need the GUI interface for verification purposes. With this issue, I can browse into the m...
Hello there,I am a Network Administrator. I have one question today. I have tried to read about regulatory domains and their effect on the wireless network. But, I couldn't identify the exact effect of the regulatory domain of devices that produce in...
Hi Guys WLC 5520 x 2on SSO Configured and it's working I'm using LAG on both the WLC's the stand-by WLC port sometimes goes offline due to which the failover doesn't take place during this time. as per the documentation from cisco we cannot set LAG a...
CISCO IR1101-K9's Cellular Interface doesn't have an option for the SLIP encapsulation. Current image is ir1101-universalk9.17.01.01.SPA.bin. Kindly asking anyone for a solution on what way to enable the encapsulation slip? Appreciate your help in ad...
Hi All I am trying to deploy an AP in the field for a rapid deployment scenario on a mine site.All of our existing fleet of 1572 APs are powered by DC and access the WLC via a PtMP backhaul system and set up as RAPs. They connect directly to the back...
Hi,Recently I tried setting up a test SSID with 802.1x using local net user and PEAP, but had problems with a client on a Samsung Galaxy s10+ trying to connect to the SSID. They are able to connect to the PSK based SSID, just not the 802.1x based one...
Hi,I’m using a AIR-CAP3502I-A-K9 access point.Getting over 300 mbs on wired (ethernet) computers, but any device (phone or laptop) on wifi will get less than 100 mbs.Is there any way to speed up service on wifi devices?
Is there a way to specifically assign the IW3700's antenna ports to either 2.4GHz or 5Ghz only or 2 Ports for 2.4Ghz and 2 Ports for 5Ghz for a 2x2 MIMO configuration? Would this be done through CLI or the GUI?
Hi everyone,This is my first post here so if I'm not posting on the right area maybe an admin move this to correct area. Also keep that in mind that english is not my native language so I might sound strange sometime. I was trying for the past couple...
WLC9800#sh verCisco IOS XE Software, Version 17.01.01tCisco IOS Software [Amsterdam], C9800-CL Software (C9800-CL-K9_IOSXE), Version 17.1.1t, RELEASE SOFTWARE (fc2) Smart Licensing Status: REGISTERED/AUTHORIZEDcisco C9800-CL (VXE) processor (revision...
Did erase nvram and rebooted the module once. Everything booted ok. Did that second time, got into this mode: AP7069.5af7.e832#Have very annoying message pops out all the time:Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255) sh...
Are there any best practices for 802.11a/n and 802.11b/g/n data rates as far as which to set as mandatory/supported etc?I'm looking at optimizing our current deployment and have started by disabling some of the lower data rates in the 2.4 range - ev...
Last Thursday (7/30/2020), our tier 1 Internet provider went offline due to severed fiber. After access was restored, we began receiving reports of users not being able to connect to the Internet via our corporate WiFi network; however, they could co...
Hi all, A bit of a strange question but my scenario is this: - I need to upgrade a few WLCs (HA SSO) from 8.3.x to 8.5.x. When I previously upgraded from 8.2 to 8.3 although I performed AP predownload (Flex), when it came to entering the reset-system...
Our plant currently uses AIR-CAP3602E-A-K9 APs and will be upgrading to AIR-AP3802E-B-K9 APs. Does the 3802 utilize the same mounting bracket as the 3602?
