We have 2802E Cisco AP. We wanted to use as wireless bridge . In older ap there was standalone mode but with newer ap whatever I read it's not supported anymore & this ap comes with mobility express. Can you set up the bridge mode in Mobility expr...
Forum Posts
Is there a way to see what SSID or even better, what AP a client authentication is failing on? We use a 5508 WLC with an ACS 5.8 for radius authentication and ACS reports only show the mac address for which the failed authentication on a particular u...
Hello, Rogue detection on AP can do that on the wireless scope. Now, about the wired scope.Is the only way to detect/alert unauthorized AP on the wired network through network vulnerability scanning tools or Cisco ISE could also do that ? Thanks,Edou...
Hello everybody, Can i link my cisco ap 1852i with a Ldap for authentication , or use a radius in AP and link with LDAP ? Thank you for all
Guys, Did anyone integrate mobility express solution with LDAP server before? As i already found the below link that contains the attached info: https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-5/b_cisco_mobility_express_8_5/b_ci...
My school got an old school building that has a AIR LAP1252AG-A-K9 in it.I know it is old, however, what do we need to use it?I was told something like an AIR-RM1552A-A-K9.If that is it, can that be made with a virtual build and not a physical one?I...
We have a 3355 MSE appliance, and we do not have the admin password for the web. I have tried just about anything (even re-running the startup wizard and redoing the password for Admin, which for some reason wouldn't take. We are at our wits end as...
HelloI have CTVM v8.10.122 and a AP2802E. I have configured a WLAN attached to the management interface, that is untagged (no VLANs in my network). The issue is that clients cannot connect to the WLAN. In the clients I can see the SSID in the availab...
Resolved! Wireless AP - Client connectivity
Hi all, I've been searching but unable to find the answer to this question. Does a client laptop's signal need to reach the actual AP for it to work or just to the AP's signal, if you have a link to any documentation that I could read too that would ...
Resolved! How to migrate mesh APs to new WLC
Hi All, I need to migrate about 50 mesh APs to a new WLC. Both the existing WLC and the new WLC are running the same code (8.3). What's the best practice to do so? Thanks,
Hi my wireless community! I have 2 setups. One 3504 with LAG connected to a switch and one without LAG (single cable). On both I'm able to ping the WLC from the switch as well as management PC (statically assigned IP in the same subnet) but unable t...
Is it possible for the Wireless AP or WLC to detect and alert on unauthorized wireless access points ? Regards,Edouard.
I am trying to join Cisco AIR-AP1562E-B-K9 outdoor AP on our Cisco 5760 WLC, but AP is unable to join the WLC.Please, advise.I tried to run below command from console# capwap ap primary-base WLC-5760 10.x.x.x Jul 6 15:18:28.916: *%CAPWAP-3-DISC_UNSU...
I'm using an AIR-AP-1142N-A-K9 in a home environment, and trying to optimize throughput. Internet connectivity is an "up to 600mbps" cable Internet service from Comcast, using their Technicolor CGM4140COM "xFi Gateway", in bridge mode, connected to a...
I feel like Cisco is straight up lying to me when they call the 1562i internal antenna omnidirectional. https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1560/installation/guide/1560hig/1560_ch1.html Look at the "omnidirectional" polar plo...
