Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

 Hi everyone, we have a completely stupid situation with the guest network.When users temporarily leaves office WiFi coverage (smoke break, usually :-)), they return inside and the guest network re-requests authorization (splash page, click "connect"...

Hello for everybody. We have wlc 3504 with ap AIR-AP1852E-R-K9 (with external antennas) registered on it. Is it possible to determine which model of the external antenna is exactly installed on this access point?

kapydan88 by • Level 7
  • 1605 Views
  • 2 replies
  • 0 Helpful votes

Hi, I'm trying to configure Multi BSSID with my Cisco 9130AXE but with no success. It does seem that the feature is supported and configurable but I no success activating it.Can you please supply detailed information on how to turn MBSSID on?Thank yo...

shlomoi by • Level 5
  • 5708 Views
  • 10 replies
  • 0 Helpful votes

Gudday allStill learning about how the Merakis work.We use MR33/52s in our network. Due to Covid restrictions some of our remote sites are unmanned.t\These sites seem to have about 10% utilisation in the 2.4Ghz band with no users registered.Have noti...

image.png
Tigers by • Level 2
  • 3391 Views
  • 2 replies
  • 0 Helpful votes

Good Day,I am setting up a network that has 2 subnets/vlans...10.1.0.0/16 and 172.16.0.0/16 The management interface of the WLC, all APs and a server running DHCP are all on the 172.x.x.x subnet. The DHCP server is configured to serve up IPs to the 1...

bob5 by • Community Member
  • 1123 Views
  • 2 replies
  • 0 Helpful votes

I am using cisco aironet C1600 (AIR-SAP1602I-E-K9) model AP. Although 802.11n is installed, the speed provided by wireless does not exceed 50Mbps. I updated the encryption method to be WPA-2 aes-ccm and enabled the WMM feature, but nothing changed. I...

Hi, I'm using wlc 9800 cl version 17.5 with SSO HA RMI+RP and one of my vWLC went to recovery mode, and i found the interfaces 1 & 2 uncheck in the checbox(which i dunno why could be like this) at ESXi network adaptor and cause the problem. I did re-...

I have a set of new 2702i's that are failing to download the correct image from the controller Get the following from the AP: Unable to create temp dir "flash:/update"Download image failed, notify controller!!! From:8.2.105.100 to 0.0.0.0, FailureCod...

RSDCisco2 by • Community Member
  • 15986 Views
  • 7 replies
  • 0 Helpful votes

Hello, On the below C9124AX Datasheet, I see that the Catalyst 9124AX has a downlink and uplink interface. https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9100ax-access-points/nb-06-cat9124-ser-ap-ds-cte-en.html Catalyst 9124AXI, ...

williamrg by • Frequent Visitor
  • 2592 Views
  • 2 replies
  • 0 Helpful votes

We are going to configure HA. But based on document, it states the higher the chassis Priority is, the chassis will be active one, and other will be standby. I want to make sure the digit value is higher, this one’s priority is higher? Is this right?...

Leftz by • Level 9
  • 3358 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card