HI allThe two c9800-ls are ha deployed, and the alarm LED of the primary device is in red. I checked the relevant information,Table 4. Alarm LED IndicatorsColorDescription Blinking Green Controller image upgradeAmber or Controller status activit...
Forum Posts
Resolved! Wireless Lan
HiOur WLAN name is the same as our 3rd partys WLAN both called (FORNET) and what I would like to know is can we have both parties connecting to the WLAN but have the 3rd party tunneled back to their WLC is this possible and if so how do we tell our ...
Dear team,Can you please help me with logging on COS AP?I found for COS AirOS APs (for example C9120AXI) are not so strong/thoroghly logs as older IOS APs (for example AIR-CAP2702E).IOS AP have on his buffer logs about clients and much more.COS AP ha...
Resolved! Inline Power Waring 9105AXW AP
Hello,I am running several 9105AXW APs with AF POE af.C9800-CL 17.3.3 controller.Is there a way to disable the Inline Power Warning LED.The APs work fine without 2.5Gbit and USB.Thanks
I set up the WLAN on the equipment of cisco wireless 2802e, but there was a problem that the SSID was not displayed on the user or wireless laptop. I didn't know the cause, so I found the log. *emWeb: Jun 02 16:58:40.350: %APF-3-SET_AUTH_KEY_MGMT_...
I have a 9800-CL WLC running 16.12.2s with ISE 2.6 patch 3.I am running into a issue getting guest portal flow working where the DACL specified by ISE authz rule is not working in the 9800. The redirect acl works fine, but after when ISE does CoA for...
What should be the reason if guest and admin network has no communication between them .
Hi, I had setup in a test lab a autonomous AIR3602i, running the code version "ap3-g2-k9w7-tar.153-3.J14,tar" - Been fine for about 3 months. Today, one started rebooting continuously - okay, so I had another, powered it up, had a base configuration ...
Resolved! Meraki BYOD solution component
Hi Merakian,Just wonder is there any Meraki BYOD solution design guide, configuration guide documentation around?I intend to create the BQ but i have no idea what need to be include?ThanksNoel
Resolved! 1562 access point
Hello,what is minimum AIR-CT2504-K9 & AIR-CT5508-K9 WLC version in order 1562 access point to connect? requirement: MESH wifi or Normal AP operate.
Hello to all, I switched from wifi 5 (2x AP3702, model AIR-CAP3702E-E-K9) to wifi 6 (2x AP9120, model C9120AXE-E).Only change, the antenna on one of them, smaller but normally more powerful, better range than others. For a reason I don't know, the r...
Access point: catalyst9120 x 40 units IOS-XE version: 17.3.1.9 Connected device: iPad 8th generation One of them operates as EWC The access point in the catalyst 9120 running as an EWC can only connect 20 devices due to the 20 device connection limit...
Hi, I am trying to get the locations of my clients, but Meraki shows only the location of the Acess Points.I have tried through the Scanning API and through the dashboard, through the scanning API the information come as follows:'locations': [],While...
Hi Guys, We are facing intermittent traffic drop issue when user is connected to SSID. He/She needs to disconnects and reconnect back to SSID then only it starts working again. Recently we moved from Aruba to Cisco 9800. All APs are in flexconnect mo...
Just curious if anyone else is seeing this problem with the 1832I's. We've had about a dozen of these models with manufacture date 6-19 fail on us and all of them have red residue on the same spot on the underside vents.
