Hi all- Before I went too far down this rabbit hole, I thought I'd see if anyone else has done this. I am using ISE and 9800 WLCs in my DMZ. Is it possible for me to specify the VLAN on the anchor side of the mobility tunnel? Do I have to somehow ...
Forum Posts
Resolved! AIR-LAP1262N-E-K9
BonjourNous avons repris une flotte de ces points d'acces.Ils sont configurés pour fonctionner avec un controleur que nous n'avons pas.Nous souhaitons avoir un firmware pour les "débrider" pour avoir un acces "web" et les paramétrer.Pouvez-vous nous ...
Scenario: a catalyst 9800 controller and catalyst series APs. In the controller, is a custom AP join profile.Historically (on AirOS 5508 controller for example), to SSH to an AP the login credentials were configured either in a global AP profile or ...
Hello, I would like to describe an issue we are experiencing. Environment: Laptop connected to corporate network via Wi-Fi A VM witout NAT running on the laptop Cisco C9800 WLC controlling the Wi-Fi network Issue: After approximately 20 minutes of co...
Hello Cisco-WLAN-Experts,while I was looking through the following document regarding trustpoint informationhttps://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/technical-reference/c9800-best-practices.htmlI found the following wrong pictur...
Hi, we recently installed a 9800vm and we have a lot of disconnections, especially on Apple devices.Does anyone know of a connection problem between Apple and the 9800 controller? I collected a user log from Radioactive Trace 7ada.27ab.2f25 172.16.1....
Resolved! CW9166i
I recently started to learn about the Meraki wifi and was going to learn it and deploy it. I went online and purchased a brand new CW9166i assuming that it will work on the Meraki dashboard. After a lot of technical support calls they told me that ...
Resolved! AP error with operation status Down.
Hi All, The question is the following: The AP joins correctly to the WLC 9800 with version 17.9.3 but when validating the radios are inOperation Status DOWN. The model of the AP is CW9164I. The policy and Tag are correctly configured as well as the c...
Hi everyone,I’m running into an issue where clients get stuck in "IP Learn" when trying to connect to a WPA3-Enterprise 192-bit (CNSA / GCMP256 + SuiteB192X) SSID.Controller: C9800-CLIOS-XE Versions tested: 17.12.4 to 17.12.5, 17.15.4Access Point: AP...
Hello Professionals,I have enabled QoS drop for some business-irrelevant categories (websites).For the test, I put QoS drop - social networking rule to my WLAN profile. However, there is one website in the 'social networking' which I want to access. ...
Hi,I've researched this issue and so far haven't found a similar case, so I've signed up to ask for some adviceI have an MR36 running 27.7.1 connected to an MS250-48LP running in test as a PoC for a network wide roll outI have a Guest SSID distibutin...
Hi everyone, Has anyone ever encountered an issue like mine where users in the LOFT office is connecting to the Ground floor office and is having intermittent issues with the connection?We've tried adjusting the TX power of each of the APs in the Gro...
Resolved! Cisco 5520 WLC FUS Image
Is there any latest FUS image for 5520 WLC?I do not see it in the Software Download page. So does that mean we don't need FUS image anymore for 5520 WLC?
Hi members having issues with C9800-CL (Version 17.18.01) connect to meraki dashboard. the firewall is configured correctly and can send traffic to meraki cloud.show meraki connectService meraki connect: enableMeraki Tunnel Config--------------------...
We have an outdoor MR76, that is also set up as a repeater to another building on campus. The building is made up of metal siding, with cinder block halfway up all around. I have no issue connecting to equipment in that building via the wireless repe...
