Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I have 2 working AP 2800 Series, both with ME functionality and version 8.10.113. They are configured and in a production network.Now I have to add to my network 15 new APs 1832 series. They come from vendor with 8.5 version and capwap firmware.How c...
Resolved! Cannot Connect AP 2702i with WLC 5508
Hi!I am super new to Cisco gear. I have intermediate experience with Juniper gear though. I am wondering if you are able to help me with my issue. I have done the initial configuration of the WLC and then I plugged my 2702i into the same switch and ...
Resolved! AIR‐DNA‐E‐3Y for C9120AXI
Hello, Would you be able to advise if I need to include the AIR-DNA-E-3Y license as I am upgrading to 9800 WLC and 9120 AP. Regards,Edouard.
I currently have 8 Cisco 2602i lightweight access points connected to our network running Cisco 3650 switches. I have all of the Agents and the Controller setup for these access points with the appropriate VLAN's configured. I was able to get access ...
Hi guys,I'm having a strange issue with an 1142 AP. I have a 5508 WLC at my corporate HQ and have AP's in many locations, connected by MPLS WAN. I have one site where the 1142 is blinking green and doesn't associate with the WLC. I have tried a di...
Is there a way to configure the 9800-CL to show the hostname of the device connecting the guest network (no auth) in the monitor -> client menu? Also is there a way to send this info to ISE or syslog?
Hi All. I got this situation that I have over 100 AP-s connected to a CISCO WLC and i need to update the OS and collect the logs (show uptime, version, etc etc...) Can someone please kindly direct me to the function/feature on how to do that with the...
Hello, everyone:How to collect log information of WLC and AP on PI, whether there is document guidance or how to operate
Hi, I'm playing around with C9800-CL and Yang Explorer. While trying to create a wlan profile, I received the error "expected tag: 'profile-name', got tag: 'wlan-id'".When I leave the wlan-id out, I got an error "/wlan-cfg-data/wlan-cfg-entries/wlan-...
Good morning, I try to install Wireless AP on to steel seat with your mounting bracket.I got manual and drawing of your Universal Mounting Bracket Detail as below picture,But, this drawing does not have detail dimension information, Could I have thes...
Hello Experts, My Cisco AP 2802 connecte dto 9200-48P swicth and getting only 15.4 watt power.Here is the output of show power inline command: Gi1/0/43 auto on 15.4 Ieee PD 4 30.0 SW5#sh power inline gigabitEthernet 1/0/43 detailInterface: Gi1/0/43In...
Hi Tech Guys, I have one mobility groups of 3 Standalone WLC with 100 AP licneces in Each controller.i have 90 Access Point and wanat to connect 30 APs to each controller Primary/Secodary/Tertiary. so if the primary down, all will be connected to Se...
Hello We have a customer, having one single site with one virtual wireless controller installed on a VM and 200 acesss points located in the Same site and connected to a single vlan ( Vlan 60 ).the customer is facing multiple performance problems whe...
I used a Cisco router, its SN 242015433. Could you tell me, when it was manufactured AND when it was sold for the first time? I am asking this, because an ISP www.almatv.kz owns the router and I am unhappy with their service. For example, why they di...
Hello guys, I have an issue with my wireless network, I have been configuring my Cisco air-ap1142n-E-k9 to an EWS 520 switch but they seem not to get IP addresses from the 2900 series router.When I connect any none cisco device to the same port on sw...
