Cisco Community

Adding local vlans to a switch running vtp

Can local VLANs be added to a switch that is running VTP (260X is the model)? We have a Core that is setup as the VTP server and a 2960X switch that is setup as a VTP client. Can I take the 2960 out of client mode, make it a VTP server, add a local...

Cisco Devices are showing offline in CBD

I have created a CBD probe in our Moncton, Canada office. The probe is connected to our Cisco Business Dashboard located in the Netherlands. However, it does not see any of my cisco devices (which are on the same network). Even when I add them manual...

How to change the AP credentials password Globally AIR-CTVM-K9

Hello,I need to change all APs Admin and enable password secrets, can i do it troughout CLI or GUI Globally?

Here we go again.. MX 3rd party VPN force over WAN2 possible?

Hi all. I award a gold star to whoever can figure this out. Been banging my head searching for any alternative or workaround. Even opened up a Meraki case for it, however after receiving an "AI" type hallucinated response and me calling them out o...

GRE over IPSec or IPSec over GRE

Isn't GRE over IPSec and IPSec over GRE both are same thing. As per my digging I found something interesting in the Cisco OCG Encor 350-401 in which GRE over IPSec(tunnel mode) is clearly said that it's also know as IPSec over Gre and it makes sense ...

Spanning Tree configuration help

I have a Cisco IE 4010 running MST connected to cisco IE 9320 running PVST connected via a single port. IE 9320 has a priority 24576 and IE 4010 has a priority 32768. Since they are running different mode of STP, that trunk port is getting blocked on...

RAVPN request control

I have a remote access VPN with the following scenario.I have FTD virtual managed by FMC (version 7.7), Cisco ISE radius AAA (version 3.4), external radius server (Microsoft NPS) for multi-factor authentication (MFA). User send the credential to FMC-...

DHCP ASA across AP

Dear all, the following debug output comes from an ASA which is acting as a DHCP server for some VLANs; this behaviour occurs only on certain mobile devices (iOS and Android) and was also observed on a Macbook, while Windows Client machines connect j...

Introducing the Catalyst 1000 Migration Tool

Hello Cisco Community,Are you planning to upgrade from your Catalyst 1000 switches to the new Catalyst 1200 or 1300/X Series?To make your transition as smooth as possible, we invite you to use the Catalyst 1000 Migration Tool. This AI-enabled tool is...

Resolved! CSPC Collector or CX Agent or CX Connector?

Hi thereA customer of mine is looking to install a Collector in order for them to get better visibility of their installed base. They have a segregated network, so they wanted to understand what would be better for them to install now, especially wit...

Cisco Catalyst Center Switch Reachable Email

Hey Smarter People,I’m running Catalyst Center and currently have Event Notifications set up to email us when a switch goes down using the “Switch Unreachable” event. What I’m trying to figure out now is how to get an email when the switch comes back...

CBS110-8T-D problem

I have a Cisco Business CBS110-8T-D unmanaged. It works normally for about ten days, and then suddenly it stops working. I unplug it from the power, I unplug the router from the power, I try everything possible, but it doesn't work. All the lights ar...

Resolved! In ACI Multi-pod, a loop is transferred from one pod to the other pod?

Hi,Since in ACI multi-pod setup, BUM traffic is transferred from one pod to another pod, does that mean if I have a loop in one pod, this loop will be transferred as well to the other pod? Is my understanding correct?And is there a way to prevent thi...

IPsec Redundancy Using HSRP

We have configured HSRP on the LAN side of the WAN router and are using BGP and IPsec on the WAN side.In this case, is redundancy required in the crypto map for the WAN-side interface?Since HSRP is not used on the WAN side, I believe it is not necess...

CSCwh93547 - Catalyst Center and Cisco ISE integration is broken

After upgrading to DNAC 2.3.7.11, we encountered a similar issue where previously working 'admin' account stopped working and we had to configure another account in ISE (with SUPER-ADMIN rights) to make this integration working again. While doing th...

Featured Content

Cisco IQ is now Generally Available

Congratulations to the Events Top Contributors Class of 2026!

Welcome Meraki Community Members!

New Heights, Clearer Paths: Introducing our simplified community rank

Community Activity

Adding local vlans to a switch running vtp

Cisco Devices are showing offline in CBD

How to change the AP credentials password Globally AIR-CTVM-K9

Here we go again.. MX 3rd party VPN force over WAN2 possible?

GRE over IPSec or IPSec over GRE

Spanning Tree configuration help

RAVPN request control

DHCP ASA across AP

Introducing the Catalyst 1000 Migration Tool

Resolved! CSPC Collector or CX Agent or CX Connector?

Cisco Catalyst Center Switch Reachable Email

CBS110-8T-D problem

Resolved! In ACI Multi-pod, a loop is transferred from one pod to the other pod?

IPsec Redundancy Using HSRP

CSCwh93547 - Catalyst Center and Cisco ISE integration is broken

Featured Content

Trending Topics

Resolved! CSPC Collector or CX Agent or CX Connector?

Resolved! In ACI Multi-pod, a loop is transferred from one pod to the other pod?