Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1983751members
1338746discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

DYNAMIC ROUTING WITH ZERO LOOPS

Hello Team,I have a topology as below;I have point to point connections to multiple partners who have different unique prefixes - to avoid overlapping of subnets.They need to access my internal resources - in this case vlan 50 and 70 for respective s...

fmugambi_0-1726837076783.png
fmugambi by • Spotlight
  • 32 Views
  • 2 replies
  • 0 Helpful votes

Firepower 1120 stuck in boot and factory reset

Hi.We have an 1120 that just blinks green in the status LED.So I've connected to the CLI via USB and can see it stops at "Creating FXOS swap file..." when booting from itself. But also if I try to boot with a new image on a USB.When I try to factory ...

MartinTG_5-1726823368179.png MartinTG_6-1726823378980.png MartinTG_2-1726823274650.png MartinTG_3-1726823284076.png
MartinTG by • Level 1
  • 75 Views
  • 2 replies
  • 0 Helpful votes

Resolved! FTD wildcard cert showing CA not available

I have imported the PKCS12 file into objects > PKI > Cert enrollmentWhen adding the cert to the device it is stating CA not available.. is this because the CA Root and Sub CA's are also required to be added to the PKI cert enrollment section?This par...

NetworkMonkey101_0-1726839499953.png NetworkMonkey101_1-1726839602427.png NetworkMonkey101_2-1726839684315.png

Resolved! Issue port-forwarding on Cisco ASA

Hello!We have a Cisco ASA running version 9.18.4.22 that we are trying to do port forwarding on. Right now an endpoint hits the outside interface ip and should forward the traffic to one of our servers that sits on the inside interface. I had set thi...

UZaman3 by • Level 1
  • 202 Views
  • 6 replies
  • 1 Helpful votes

Cisco ASR 1001-X IPv6 issues with ACL's and encapsulation failed

hi guysI'm having an issue tuning my IPv6 outbound flows on the ASR1001-X (1Gen) and my struggle is that MTR is now showing the IP address of the router itself or showing the packet loss on the level of 90%. All other hops are fine and at the end my ...

CUCM DRS backup device error

Hi all,CUCM 11.5.1.12900-21Rocky Linux 9.4, OpenSSH_8.7p1, OpenSSL 3.0.7 1I am attempting to set the Rocky server as a backup device for CUCM.  I initially got the errors regarding key exchange algorithms and host key types not matching, so I enabled...

PACC by • Level 1
  • 71 Views
  • 1 replies
  • 0 Helpful votes

IPsec over NAT444 issue

Hello Everyone I have to set up an ipsec tunnel with Lo0 as source of tha tunnel. Nat is activated in My CE and in the ISP level (NAT444)All ipsec and Nat configuration is ok but, and as I know that for the NAT to work correctly, the packet should pa...

mrkassimi by • Level 1
  • 56 Views
  • 1 replies
  • 0 Helpful votes

Cisco 9500 SVL

Hello Anyway to configure the C9500 switches SVL with essential license.Appreciate your helpThanks

Load more