Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi I am a looking to get into old ISR Cisco module for a tftp server and also to use it for connecting my Cisco ip phones I got at a recycling store any ideas on where to get like Cisco 2800 series or similar machines in India for cheap??
Hello, I already assigned lower specification for virtual cisco SMA on Microsoft hypervisor. i need to assign higher resources for the SMA. what is the best practice steps to this.
Hello all, On Border Edges(DC01-BE001-6/7) am trying to advertise default route from GRT to MPBGP-EVPN but not able to do it properly with the following configruration. Thanks in advance for tips and correction **************************************...
Hello Freindswith Regards to ACI with DMZ Servers can we provision the DMZ Servers (Web-DNS-Mail) directly on the ACI Fabric in Main Tenant aka(Production Tenant) instead of having Dedicated Tenant for DMZ Servicewe Already have PaloAlto at Internet ...
Hello Freindsfor ASA in Active/Standby Mode connected to ACI , do i need 1 IPG(vPC) For Both or Just 2 IPG 1 for each device? I know 1 IPG for both ASAs if they are in Cluster Mode but confused in Active/Standbythanks all
Hi All,Recently, we migrated our enterprise Wi-Fi authentication method from PEAP to TEAP (inner auth EAP-TLS). Since then, many users have been experiencing disconnections while their sessions are active.In the morning, the Wi-Fi connects and works ...
I cannot find anywhere if the local admin account for FDM has a break class in any documentation. If say the account has been compromised. Can we console into the cli to reset the pw or do we have to reimage firepower and reload the configs?
I have 3 DNAC server nodes. I finalized the conf for the 3 and created the H, A, but after I turn off the devices and turn them on, the attached log error message appears for me using maglev most of them (CrashLoopBackOff)ndp pipelineruntime-taskmgr-...
I have a Cisco Nexus 5672UP switch running NX‑OS 7.3(6)N1(1). The switch was functioning normally, but after performing a reset, the Ethernet ports on Slot 1 (ports 1‑48) are no longer visible in show interface status or show interface brief.
Hello, I'm currently configuring a site. They have isp that uses a radio link. I been having issues when the internal networks reach out to the internet that they are super laggy and slow speeds. Has any configure a site that instead of having a actu...
I know it's a very silly question to ask, but I want to know whenever we create a vlan with vlan vlan-num e.g. vlan 10and then till we don't use exit and came back to configuration mode the vlan doesn't show up. Like why we have to explicitly 'exit' ...
Hi,I am referring to the Figure 5-25 from the book Cisco Catalyst SD-WAN: Design, Deploy, and Secure Your WAN: It states: "The workaround is to create loopback interfaces in bind mode at the hub for remote branch colors that are not physically presen...
cp8851 asking for acitvation codeit was working for during router / electrical outage it recycled and now asking for codethis is new phone and no code in box.
I’m trying to access my desktop remotely through a VPN I set up on my router. However, I also need to use the Cisco VPN for school in order to access certain software. Ideally, I’d like to have both VPNs active at the same time. While they technicall...