Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2044864members
1401788discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

OSPF vs STP cost behaviour

Hi all,In Spanning Tree Protocol (STP), the path cost takes into account the cost of the incoming interface, whereas for OSPF, I need to consider the cost of the outgoing interface.Is that correct? If yes, is there a specific reason behind this diffe...

honelbokel by • Community Member
  • 68 Views
  • 3 replies
  • 0 Helpful votes

PC terminals under 9120AX are randomly disconnected

We are using about 80 PC terminals with about 3 APs for training new employees, but when a terminal that has an unstable connection and is disconnected is reconnected to the wireless LAN, another PC terminal is disconnected.Monitoring > Wireless > Ra...

DNAC: Bug Trend 2025 CY01(1-3)

本記事では Cisco DNA Center に関する既知不具合のうち Service Request (SR) での報告が多かった Top 5 を 1ヶ月ごとにまとめています。 本ランキングは TAC SR による問い合わせをベースに集計しており、Partner や User 自身で解決したケースは報告数に含まれません。 2025 年 1 月BugIDTitleCSCwj15477Delete device failed with error delete on table protocole...

hidyano by • Cisco Employee
  • 6 Views
  • 0 replies
  • 0 Helpful votes

9130AX will not save pre-stage configuration

Hi,We have a batch of 9130AX's that will not save the pre stage configuration, no invalids are seen on the CLI.Adding hostname does not change the device from MAC to given hostname and when sh cap cli conf is applied control names and IP's are missin...

WLC 9800 MAC filter multiple wlan

Hi friends, I'm configuring a WLC 9800 17.9.4.a. MAC address filtering works, but it doesn't respect the WLAN space.For example, I want MAC01 to connect to WLAN profile Test02 but not to WLAN profile Test3, and I want MAC02 to connect to WLAN profile...

LeoTI_0-1743536532606.png
Leo TI by • Level 1
  • 96 Views
  • 2 replies
  • 0 Helpful votes

vmanageDB restore failed

It is an on-premise environment that cannot connect to the Internet.version vmanage: 20.15.1 vbond: 20.15.1 vsmart: 20.15.1I performed a backup and restore of vmanageDB by referring to the following site. https://www.cisco.com/c/en/us/support/docs/ro...

2nd Switch in a C9300 Stack as a hot spare

I am replacing a single 9200CX switch with a 2 switch stack of 9300s.  The existing switch is aggregating a handful of point to point links to remote WAN sites that need access to a shared server.  These links are either dark fiber, layer 2 leased li...

Aireos and 9800 controller mobility tunnel compatibility

Dear Alli have cisco 3504 controller running  8.5.182.108 at small site i want to upgrade it to Release 8.10.196.0we have existing mobility tunnel between 3504 and 9800 controller for guest WLANi have question that  8.10.196.0 is compatible with 9800...

NX-OS commands vs IOS-XE commands

We are trying to setup DoD CAC login via SSH. There are some commands shown in a document for setting up things on an Catalyst 9300 IOS-XE but need to configure a Cisco Nexus 9000 also. The commands in the picture are what we need to do on the NX-OS....

image.jpg
Load more
Top Solution Authors
View All