Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2135259members
1465023discussions

Featured Content

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Resolved! Download c1140-k9w7-tar.153-3.JB.tar ?

Hello all !    I'm searching where i can download this software "c1140-k9w7-tar.153-3.JB.tar" for my access-point.   Can you give me a link where i can download it please ?   Thank's

Ipefixe by • Level 1
  • 21281 Views
  • 4 replies
  • 0 Helpful votes

Cisco Packet Tracer Network Scanning

Not sure if this is the right place for this questions but... I work at a place that using the Cisco Packet Tracer software and have been for years until today. We have been banned from updating to the new PT version of 9.0.0 because our security/ ne...

webbjh by • Level 1
  • 121 Views
  • 4 replies
  • 0 Helpful votes

CCNA EXAM LAB QUESTIONS

Hi, I'll be sitting my CCNA exam in Feb of this year. Regarding the lab questions in the exam, do i have to type out the full command when in the CLI? eg: Could i just type "en" instead of "enable" or "conf t" instead of "configure terminal" ??Any ad...

Jameztee by • Level 1
  • 213 Views
  • 2 replies
  • 0 Helpful votes

BPDU Guard

Just a simple question why it's recommended to use both Portfast and BPDU Guard together apart from the very fact that both should be used in access switches ports connecting to end users?? Like BPDU Guard will still work if I don't have portfast con...

Routing to SVI Over Trunk in IOS XE - Can reach hosts but not GW?

Good morning Cisco Community, I feel like i am over  looking something simple here. I've built a SVI and propogated it into OSPF  on a L3 device. On one interface of that device there is a host connected through two cascaded layer two acces switches....

jbulloch by • Level 1
  • 115 Views
  • 2 replies
  • 0 Helpful votes

Need assistance in fixing the uccx script

We have one script that was downloaded from the old UCCX 8.6 system and then uploaded to the new UCCX 15 system. When using this script, I am unable to answer calls from the Finesse desktop, although I can answer the calls from the phone. The other s...

ziakhan86 by • Level 1
  • 93 Views
  • 0 replies
  • 0 Helpful votes

Cisco 2802i AUX Port as LAN Port

Following the instruction from the link below, I converted the AUX port of one of our Cisco 2802i AP's to a LAN port. My hope was to feed a switch from it so I could provide network access to three devices. So far, I can not gain network access. Has ...

SHHOSP by • Level 1
  • 104 Views
  • 2 replies
  • 0 Helpful votes

IE-9320-24T4X-E Port Configuration change

I have multiple setups with these network switches. At least on two different setups, we have connection issues with one of the ports (port #24). We verified that the port configuration has changed and the reminder of the ports configurations remain ...

eddie8 by • Community Member
  • 174 Views
  • 5 replies
  • 0 Helpful votes

Set an apply group via netconf on ios-xr

Running this netconf call via ncclient fails to apply the apply-groupdef main(): apply_group = """ <config> <interface-configurations xmlns="http://cisco.com/ns/yang/Cisco-IOS-XR-ifmgr-cfg"> <interface-configuration> ...

tanner2 by • Community Member
  • 196 Views
  • 2 replies
  • 0 Helpful votes

IOS-XE Ignore Radius VSA's

I was curious if on the Cat 9k series switches, is there a way on a port (or many whether individually or globally) to have the port ignore any VSA attributes sent back by the radius server.  Like if I want to ignore the VLAN or the IBNS template tha...

Community Manager reflections on a celebratory year!

What an incredible year it has been as we celebrated the 25th Anniversary of Cisco Community! From exciting contests and vibrant social engagements to amazing prizes, this milestone has been truly spectacular. We were honored to connect with many of ...

Screenshot 2025-11-25 at 12.47.59 PM.png
Load more