Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello, my iOS on C887VA-M-K9 is complaining about heat issues on boot up with VDSL 2 board. I'm wondering if I have an issue of thermal paste, since internally there is none visible clues fan ever existed. I bought this unit used to replace my C887M-...
Hello Community, We are planning to change the FMC IP.The FTD is already onboarded and in sync with FMC (production environment), so factory reset or config loss is not an option. To update FMC IP on FTD, we need the registration key so is there any ...
What an incredible year it has been as we celebrated the 25th Anniversary of Cisco Community! From exciting contests and vibrant social engagements to amazing prizes, this milestone has been truly spectacular. We were honored to connect with many of ...
Hello, everyone. IS-IS has a mechanism called the three-way handshake that is enabled on P2P links. It is defined in RFC 5303. The basic mechanism defined in the standard is that each side declaresthe other side to be reachable if a Hello packet is h...
Hi All,we recently installed Cisco Room kit EQ codec and Cisco Room Bar (Standalone - BYOD). we also purchased Cisco Active USB-C Cable 9m (USB-C 3.1 Active Optical Cable, 9M length) as it will allow us to remove HDMI cables and chargers while using ...
I am a CCNA student and I recently bought a SGE2000 10/100/1000 Switch to play around with. I set it up and but I am having a little difficulty getting into the switch to configure it. This switch has GUI so I opened my browser and typed in the de...
I'd like to set up the communication btw a Linux VM in public cloud and Cisco virtual router C8000V (version 17.9.4a) in our DC via vxlan overlay networking based on IPsec tunnel. here is C8000v config: int loopback1 ip address 10.200.200.1 255.255.2...
Today was a bad day for the Cisco CBS250 and C1200's. I've been running these for 1 to 2 years now and haven't had an issue until today. I think every single one crashed today and kept crashing until I removed the DNS configuration. I have about 50 o...
Hi All. Getting the below alert, can some one help please how to metigate and reason of port flapping. Interface TenGigabitEthernet0/0/11, link down due to MAC local and PHY line side fault. Transceiver Rx optical power is too low (-40.0 dbm)
Hi,According to the below datasheet of C8300, I understand that C8300 supports GRE.However, there is not a clear mention about IPIP tunneling and I think that C8300 does not support it.Is it right?https://www.cisco.com/c/en/us/products/collateral/rou...
Dear Community Members.,I am having issues with my Cisco anyconnect VPN :The VPN suddenly stopped working with an error message of Expired License:Below is the Content of the Directory: ANYCONNECT_CYB#dirDirectory of flash0:/1 -rw- 104193476 Mar...
What does transceiver not allowed online mean?%TRANSCEIVER-6-INSERTED: Chassis 1 C0/1: iomd: transceiver module inserted in Te0/1/1 %TRANSCEIVER-3-NOT_ALLOWED_ONLINE: Chassis 1 C0/1: iomd: Detected for transceiver module in Te0/1/1, module disabledSF...
Hello friends.Few months ago, I carried out ISE two node deployment and Configured several policies as we were going to get licensed version.Purpose was testing and learning. I almost configured all of things I wanted. Yesterday, I signed in ISE and ...