Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Hardware advice needed
by ammahend -
Request for Legacy Software Image for Cisco 1812 Router
by PosTerieur -
Procedures for keeping cold spare equipment
by ColForbin -
Forcing A Cisco Catalyst Switch To Use 3rd Party SFP Modules
by gtstech -
IOS-XE: snmp-server enable traps 設定で送信される Trap の OID
by Reiji Kimura -
Secure Network Analytics: Proxy設定について
by Akihiro Sumida -
HA without setting all interfaces with static IP addresses?
by jjevans1 -
A9K-20HG-FLEX-TR Maximum Full-Duplex Line Rate With FC 3
by rainow
Community Activity
Hardware advice needed
Hi Team, do you see any issue with this setup in terms of operations, don't worry about RF. Any experience or advice is appreciated, GNSS antenna is not shown but is included on mesh side.
ISE : ISE 3.3 バックアップとリストア方法
はじめに1. 取得対象機器2. バックアップの種類3. 事前準備4. バックアップ手順5. リストア手順 参考情報 はじめに Cisco ISE の設定データのバックアップ方法と、リストア方法を紹介します。なお、本資料は Cisco ISE 3.3 を使用して作成しています。基本的な手順は Cisco ISE 3.x と変わりありませんが、画面表記がバージョンにより異なる箇所が含まれていますので、ご注意ください。 1. 取得対象機器 Cisco ISE のバックアップは...
SD-WAN : PnP Portal 上の "Pending(Redirection)" という status について
はじめにPnP Portal 上で表示される "Pending(Redirection)" について参考情報 はじめに 本ドキュメントでは、PnP Portal 上で表示される "Pending(Redirection)" という status について記載します。 PnP Portal 上で表示される "Pending(Redirection)" について PnP Portal に機器を登録した後、以下のように "Pending(Redirection)" とい...
Mobility Express To 9800 Wireless LAN Controller
Hello,I am new to the Cisco Self Standing Wireless LAN Controller System. I have always used Mobility Express, and I know it is end of life. The purpose of this AP is for learning and using it in my home lab. I have read this post below:Migrate ME to...
Can not get Internet Access [or nat translations] on my ISRC1111
Hello I am working multiple setups but this one was supposed to be easy, until it was not. I am sure I am overlooking something tiny, but nevertheless. Long story short; here is my config and I get not get any NAT translations and or any internet a...
Roombar USB-C - Video, Screen Mirroring but no sound
Hello,I’m encountering an issue when connecting my MacBook to a Cisco Room Bar using a USB-C to USB-C cable.The Mac detects the Room Bar correctly.Screen sharing works as expected.The Room Bar’s camera and microphone also work properly.However, there...
Cisco Firepower 2110 Threat Defense SQLNET inspection issue
Hello Cisco Community!We have a situation where we need to disable SQLNET Inspection in the FMC Cisco Firepower 2110 Threat Defense.I would appreciate your guidance on how to do this using the GUI and the command line.I found the information about...
Mute Permissions, Locking Mute
When an attendee mutes themselves, they retain the ability to unmute at will. The picture shows three attendee microphones, with the top and bottom mics only allowed to unmute when requested by a panelist. The middle mic, is able to mute and unmute ...
Feedback Issue with Room Kit EQ and Ceiling Microphones
Hello Cisco Community,I am currently facing an issue in one video conferencing room equipped with a Room Kit EQ, three analog ceiling microphones, and audio output through the TV's speakers. The problem arises when remote participants speak; we can h...
Procedures for keeping cold spare equipment
I have what appears on one level to be a basic question. I was tasked with coming up with a plan to support 2 remote sites that don’t have IT people. Each site has an ISR4400 series and a 9200 switch stack with 2 switches. There is a spare 4400 and a...
Request for Legacy Software Image for Cisco 1812 Router
Hi,I’m currently working with an old Cisco 1812 router and recently noticed that it’s running a different software version compared to my other 1812 routers still in production. Unfortunately, I no longer have a copy of the image file — c181x-advipse...
Resolved! Enabling application visibility in Flexible Netflow packets via NBAR
Hello guys I'm having a little trouble with NBAR and I'm hoping someone could be of help. So I've just deployed SolarWinds and I'm trying to enable NBAR on Cisco C9404R switch for deep application visibility. Then have the NBAR data applied into Netf...
Cisco UCS Platform Emulator 4.2(2aPE1)
Cisco UCS Platform Emulator, Release 4.2(2aPE1) CONFIGURATION IMPORT NOTE: Importing configuration backups (All, System, or Logical) taken from the UCS Platform Emulator (UCSPE) to physical UCS Manager domains is not recommended or supported by C...
C9300-48S with different power supplies
Hi, I have a question please regarding the C9300-48S as it comes by default with 715W power supply but when choosing a secondary power supply, one of the options is a power supply with 350W only, how to confirm if the 350W will be enough to handle al...
N3K to N9K replacement - Info required about licensing
Hello Expert ,We are replacing the N3K device with N9K .We could see N3K has LAN_BASE_SERVICES_PKG license whereas in new N9K device there is no license ..Will this have any problem after the switch replacement ?N3K : N3K-C3048TP-1GE ...
