Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1999769members
1360323discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

C1111 dynamic and static IP on same interface

Hi, I have a C1111-4P device in front of a Comcast internet connection. Recently Comcast changed things and now if you want to access the diagnostic page of a standalone cable modem connected to your router, you have to NAT outgoing packets to be wit...

WLC 5520 Upgrade Issue

Hi guys, i am having a weird issue post upgrade of HA WLC 5520 from 8.1.102.0 to 8.5.164.0. The previous active unit is standby and current active box i do see APs associated. The problem is when i failover the WLC, the actual active unit unable to g...

kishen32 by • Level 1
  • 1952 Views
  • 8 replies
  • 1 Helpful votes

CBS350 Allowing Inter-VLAN Multicast

I have multiple CBS350 switches on our site and after installing some new security software, I became aware that multicast traffic seems to be traversing between VLANs. I initially saw this on one of my sites that's using older SG200 switches so I th...

Resolved! Calling Name being stripped from SIP headers

Hello, I have a customer with CUCM 14SU1. They have recently purchased a VG410 which has 48 FXS ports which connect analog phones at one of their sites. The VG410 is not supported as an SCCP gateway until CUCM 14SU3 so I have set it up with dial peer...

CSCwk48338 - AX AP doesn't accept clients

Man, there has to be another solution other than upgrading to iOS 17.12.3 .. We can't use that IOS because we still have 900 2702's on our controllers.  We have 1500 9130's and 2800 3802's.I really wish Cisco would escalate this issue and get a patch...

ASA Static Routing same IP with different subnet masks

HiWould having static routes on an ASA with the same IP but with a different subnet mask present any issues?For example:192.168.0.0/16192.168.2.0/24From what I understand it wouldn't present an issue because although they may have the same IP, the su...

tselby3 by • Level 1
  • 21 Views
  • 2 replies
  • 0 Helpful votes

Catalyst IE 3400H 24T Stuck in POST Mode

I have a new from supplier 3400H switch that let me go through the Day 0 configuration and initial setup. Power cycled at the end like i have always done to other setups to verify the settings stayed and the switch came up and continuously flashes th...

a-e by • Level 1
  • 68 Views
  • 3 replies
  • 0 Helpful votes

Cisco IOS XE Network Operations using API

Hi,Is there a yang module for RESTCONF that can be used to carry out cli commands, like ping and certificate imports. There is a yang module for icmp, but that appears to be configuring icmp rather than actually carrying out a ping. For certificate m...

Simulating service provider ISDN Network Terminal

For testing purpose , i need to simulate a telephony service provider network terminal (Italy here) with an old Cisco 1751V (or 1760)Mi BRI config is :voice-port 0/1 compand-type a-law cptone IT interface BRI0/1 no ip address isdn switch-type basi...

Oknet by • Level 1
  • 64 Views
  • 1 replies
  • 0 Helpful votes

Best Practice for Switch Stack Uplinks

What is everyone's best practice for switch stack uplinks?If there's a stack containing 8 switches and we can fit 8 uplinks in a port channel, should there be an uplink from each switch in the stack?  Or 2 uplinks (master + standby), 2 Uplinks (membe...

MikeMoss by • Level 1
  • 56 Views
  • 3 replies
  • 1 Helpful votes

Resolved! ISE 3.2 Upgrade - Error loading Certificates

HiI recently upgraded from ISE 2.7 patch 7 to ISE 3.2 patch (full upgrade workflow).Deployment is 5 node: 2 PAN and 3 PSN. Since the upgrade, I can't access the System Certificates of the other nodes in the deployment from the PAN (secondary PAN and ...

Console cable + Putty problem

Hello Everyone , i'm experiecning a problemr with a Cisco 3825 routers , i got a black screen when trying to console into devices ...The same issue occurs with 2 differents devices (both 3825) .i'tried to adjust the speed with many different values b...

Kirollos by • Level 1
  • 35 Views
  • 0 replies
  • 0 Helpful votes
Load more