Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2133636members
1464161discussions

Featured Content

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Help - layer 3 switch to router to Internet

Hi I am having some issues setting up a 2821 to pass internet traffic from a internet router to a layer3 switch.the switch and a pc connected to the switch can ping the outgoing interface on the router but not the other side of the link.The router ca...

High-Density Videoconferencing over Wireless C9800-40

Hi guys,I’ve been working in wireless for about five years and have never seen videoconferencing devices working in a wireless environment. My question is: Have you seen this? Does it work well?My intuition says it’s a terrible idea, but maybe I’m wr...

HiddenAir by • Level 1
  • 160 Views
  • 4 replies
  • 0 Helpful votes

Resolved! ASA 5525 Firewall failover setup.

We have two Cisco ASA 5525 firewall at Block A and Block B where the failover was not setup yet. Should i need to configure one port at firewall and install new physical fiber cable with transceiver for peer to peer connection?  

ITCompMinco_0-1763974294363.png

Cisco 9400 power supply "power-off"

We've got a concerning output when we check the power supplies in our dual 9400 core.  We're using PS3 and PS4 in the two units.  All four power supplies are connected to a good source.  PS4 on Core 1 is connected to a 125V power source, the other 3 ...

cisco SSE ZTNA issue with SMB Traffic

Hello Community,we are facing an issue with the SSE Ztna when we are trying to Access SMB server through a Tunnel. the behaviour is so strange when we have tested with Customer org Laptop it is not access the File server but from a laptop not from th...

Call Queue and Weighted Routing

I am in the process of setting up a new call queue and the user would like a priority-based route type using the Weighted method. We've usually done simultaneous, so this is new for us. I don't see anything in the documentation for how the weighting ...

svanatta by • Level 1
  • 124 Views
  • 2 replies
  • 0 Helpful votes

anyconnect ssl vpn issue

i want to establish a clientless SSL VPN connection to the ASA to download the AnyConnect clientsoftware.i logged in from remote host which is pc-c from browseri enteredhttps://209.165.200.226 for the SSL VPN but i cannot reach what is/are issues? p...

Screenshot 2025-12-29 183119.png

Packet duplication statistics

Hi,I am trying to understand packet duplication statistics, and I can't find consistent information.show tunnel statistics packet-duplication tunnel stats ipsec 10.10.0.1 10.10.0.2 12366 12346 pktdup-rx 325 pktdup-rx-other 0 pktdup-rx-this ...

iores by • Level 3
  • 291 Views
  • 7 replies
  • 0 Helpful votes

Nexus 9k or Catalyst 9k for ToR iSCSI SAN and VMWare

I am looking at upgrading our Top of Rack Nexus 5k switches to new 9k models.  These racks are for our VMWare Servers and iSCSI SAN devices (both Dell).  I have always used Nexus switches for this rack (since it is storage) and Catalyst switches for ...

IP retrieval - SG350 28P

Hello,I am attempting to find the IP of my switch to log in to the web GUI. The vendor who installed it has deleted our project folder and has no information. I am connecting to the switch via Cat6 (with RJ45 / USB adapter) to my windows 11 laptop. T...

asmol by • Community Member
  • 126 Views
  • 2 replies
  • 0 Helpful votes

VTP Pruning

Can someone help me understand the concep of vtp pruning.In my topology SW1 is the server and the rest are clients. Vlans configured are 10,20,30,40So as far as I know if vtp pruning is enabled and  a device in vlan 10 ping to another device on vlan ...

Load more