Hi,I have the following questions can we run a HA link of firewall(Fortinet, Palo) over ACI multipod. Do we need to take any special considerations into account recording the ACI endpoint learning beheaviour? Frederik
Forum Posts
Hi Team , logs for the EP attaching and detaching to and from the Fabric shows IP as 0.0.0.0( as shown in the screenshot below ) . Can someone please explain why does it shows as 0.0.0.0 and does it indicate any issue . I am able to ping the server...
Hi there.In order to do a health check of ACI's nodes, I was trying to get the global temperature from each node by API REST.The output is similar to the 'show temperature' command:C220-FCH1807V02V /sensor # show temperature Name Sensor Reading Units...
Does anyone know of any way to remove the F0546 fault code by any other means than squelching all faults with this code? F0546: fltEthpmIfPortDownNoInfra Explanation: This fault occurs when a port goes down Recommended Action: If you see this fault...
Hey all, Regarding the ACI MSO/APIC, Knowing that RTT between 2 MSOs = 150 msec and RTT between MSO/APIC = 1msec. What is the behavior of the MSOs and APICs when RTT is not met?Does it have any influence on the control plane of the fabrics? Thank you...
For the record, the client I am at has no monitoring of links / infrastructure at the moment. I am trying to find the bottleneck for a bandwidth issue. Replication across the IPN (Multi-Pod), does not go as high as it should (results +- 100M). Smalle...
Resolved! Cisco ACI 5.2 no longer long-lived?
Hello all,Back in August Cisco had given notice that the 5.2 version had been added to the list of long-lived releases, and the 3.2 branch had been removed from that list.https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/recommend...
Resolved! 3-node MSO Upgrade
Hi Team,In regards to MSO upgrade, I have been referring some documentation of Cisco and I did not get the exact answer. Please assist -We are planning ACI Fabric Upgrade(3 APIC, 2 Spine, 6 leaf, 3-node MSO).APIC - 4.2(1j) Spine/Leaf - 14.2(1j)MSO - ...
Resolved! ACI EPG's in a freeze state
Hi Everyone, Below is an error message that i detected on the ACI fabric and was not very descriptive to investigate on which EPG's are in the freeze state.I had a look on the internet and could not find much information, besides a 'show command' to ...
Resolved! Redundant DHCP Relay in ACI
Hello,i am wondering what is the best way to provide redundant DHCP-Setup in ACI.it is important to understand that in our environment the dhcp-servers are not a cluster but standalone machines. therefore we need to add 2 of them to the Bridge Domain...
Hi all,i just installed on our server the ACISim 5.0-2h. As you can see from the attachment i correctly provided the OOB IP address, the GW, and put the Interface on Eth1 VLAN85 (where other VMs have their mgmt interface and i correctly reach, includ...
Hello I have cisco Prime Perfermonce version 1.5.0.0 and i have error with alarm majour . i give a picture that show more details. so i wait from expert Prime cisco give me a solution for this alaram thanks in advance
Hello,I installed the ACI simulator software in a VM ESXI 6.5 .The APIC is up and running and i find the first leaf is there to be registered. After i register the leaf to the pod, it appears as registered but in "Inactive" state. For sure the spine ...
Hi Team , How the communication between source 10.10.10.49 and destination 10.10.10.52 works if they are configured on the ESXI host and are behind the same interface of ACI LEAF-3 & LEAF-4 switches and on the same vlan . Source : 10.10.10.49 Desti...
Hi, Community.We have a production Leafs -> FI -> UCS Chassis w/ VMM Integration and it's working well. Now we have a user case that a blade server in the same UCS Chassis (aka Uplink to FI then Leafs) needs to join the existing EPG, how can I achiev...
