Hi all,Just wondering....Is there a sane reason why node numbers in ACI max out at the number 4000?Now I understand working with processors where every bit counts (yes, I did write machine code for the 8 bit Z80 at one time in my life)But last time I...
Hi experts,I always like a picture!As the picture shows, there is a VPC configured between leaves 2201 and 2202.There is continuous traffic flowing between all four servers.But my question is, why doesn't Leaf2201 see the webserverbm (10.218.12.10) a...
Hello Experts , I am trying to trace the endpoint 10.10.10.18 from source connected leaf switch .From the below output I can see to reach 10.10.10.18 we have to go via tunnel23 ...How do I check next from cli ? what is the command to check the tunn...
I have installed the 5.2-1g version of the simulator as a VM using VShpere 6.7 (There is no access to the management IP address. The VM shows as being isolated. Cannot ping it or http.I cannot ping the gateway. Cannot login as root. Also discovery of...
Hi folks,OK. I know I can run the following command agains a leaf to find the Spine anycast proxy addresses,apic1# fabric 2202 show isis dteps vrf overlay-1 ---------------------------------------------------------------- Node 2202 (Leaf2202) ------...
Hi,Recently some ACI Leaf-Switches did a reset reason: reset-triggered-due-to-ha-policy-of-resetService: epm hap resetVersion: 14.2(2f)Hardware: N9K-C93180LC-EXI cant understand why this is happening
I have reviewed the Events and Audit Logs and in the Events tab I found a lot of records like this : uni/usersessext/delsession-oKX0GAPrTV6IJZzVIhOEaQ==Createduni/usersessext/actsession-4j9PF3KyRViDkqcXR4Lf_w==Deleted I have more than 100 pages with ...
Hello All, I have a home lab and decided to add an ACI environment since I am studying for CCIE DC.Got APIC-M3 appliances, one spine, and two leaves.unfortunately, I did not know this caused an issue and did a dumb thing and installed ESXi on my APIC...
Hi Everyone, I am currently working on a small project in which i have to delete alot of unused static ports. Now as i was going about i was wondering how i would know which port is being used and which isnt.. so i figured out that i could moquery fv...
Hi everyone,We have some issues with our ACI connection between 2 POD. The 2 EPGs between 2 BD on the same VRF that are located between 2 POD can't access each other. BDVLANxxx: EPGVLANxxx : POD1 : DCBDVLANyyy : EPGVLANyyy : POD2 : DRCWe are using ...
@cisco aciHow do I check firmware version of leaf switch ssd
please help me to check the ssd log, I want to know the problem of the ssd lifetime, thanks!F3073: fltEqptFlashFlash-worn-out (90% lifetime)
Good Morning,I have a Cisco ACI in 5.2 version in my LAB with a customer tenant configured. I need make some changes in bridge domain configuration to configure subnet ip address and associate it to outside L3. The customer has 4.2 version and I´ve c...
Hello everyone, I'm trying to install Multi Domain Manager from the Cisco DC App Center: https://dcappcenter.cisco.com/multi-domain-manager.html but got an error after I upload the app on the APIC : Failed to install application Multi Domain Manager....
Hello Community, I created a small ACI Lab and finally I found an old APIC-M2.According to the BIOS, the TPM module is owned.However, if I start the installation of the APIC, the installation fails.As soon as I disable the TPM and install version 4.0...
