Hi, Reading documentation on WAAS 694 , it says that it can do 2,500 connections and a lic upgrade is required for 6000 connections.I cannot find the lic part number on cisco.com.Can anyone please help me with this understanding or does WAAS 694...
Hi,I've configure two ACE 4700 in a SLB modus http to a web server.To understand how the ACE works and to see if all are ok, I want to test it? but how?How do I do to initiate a http connection between my test pc to the webserver through the ACE?Than...
We have loaded CSS release 8.20.5.1, but our 11503 pair rebooted after a week so we wanted to rollback to 8.20.3.03.I ran the upgrade script and loaded 8.20.3.03, but on reboot the old ver did not get written to the modules, als operational flash is ...
Hican the proxy list crash? if so, how can I fix it?today, I need add a few ssl-server commands into the list, but, I can not active, the error is:Error in ssl-server 38: RSA Cert/Key Verify%% Key file is in valid.which the ssl-server 38 is not the ...
Hi, We are having problems with our css11503 failover arrangement. We see vrrp-mac flapping in the switch where the two css11503 are connected (master and backup). This behavior causes that some Cointainers stop responding requests from users. We ne...
Dear Fellows,I have the following working scenario:I am using ACE Module for Server Load Balancing in 6500. I have configured it in Routed mode.I have configured a VIP which works well from Client and Server Side. Whenever a Client sends traffic to V...
I am in the process of Migration all servers from our Content switch to CIsco ACE4710.one content has this line itemadvanced-balance sticky-srcipWhat would be similar option in ACE.?Thanks for any help on this.Mehdi
Hi there , I have WAVE 574 (not central manager ) running Version 4.2.1 . I suppose to upgrade the version to 4.4.5 . Is that comaptible ? or anything else i need to care about ??Thanks & Regards,Ram
Hey,I have a requirement to load balance OWA 2010 inbound connectivity to 2 CAS servers using a ACE 4710 with sticky sessions enabled.The CAS servers are currently responding on 80 or 443 at this moment in time. Eventually I want to off load the SSL ...
Hi Does anyone know what the maximum acceptable latency is on a FT Link between a Pair of ACE30 modules configured as a FT Pair with multiple contexts running active/active.I am trying to ascertain if it is possible to site in different DC's seperate...
Hi.We have an ACE30 (running A5(1.2)) and a couple of Exchange 2010 CAS.We have little experience in load-balancing, but we found this guide from Cisco: http://www.cisco.com/en/US/docs/solutions/Enterprise/Data_Center/App_Networking/Exchange_VSphere_...
Configured ACE in routed mode ,and have the vlan ,route-map defined on th switch.Able to ping the server vlan ,and servers from the ACE ,but unable to ping the vip from ACE ,but able to ping the gateway for the client vlan.Attaching the config the of...
Hi all,i have a query on layer 3 load balancing. Please refer to the following example and config,service Aip address 1.1.1.1keepalive icmpactiveservice Bip address 1.1.1.2keepalive icmpactivecontent Cvip 10.10.10.10add service Aadd service BNow for ...
I can not find any information on the cluster licence for WAAS Mobile. I assume this is needed if you want to run redundant servers. Or how you orderCan anybody supply a good link, or explain what I need?CheersAndy
Hi guysToday I got a customer that installed a WAE device on its LAN environment.Basically, they engineering team, for some reason, did not allow to be directly connected to our router so we have the WAE device on a different vlan from the router sub...
