Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Wednesday, September 21, 2024 through Friday, October 4, 2024. Our colleagues Arpita Dash, Prateek Upadhyay and Udhay R. will be waiting...
Forum Posts
Resolved! DNAC - Config backup system requirements
Hi All,Just want to know how much hard disk space is required on (Red Hat or Ubuntu) for DNAC config and devices configurations backup ?Regards,Talha
I purchased a used Catalyst 1000 16-port switch (model number C1000-16P-E-2G-L). Though the seller had stated the switch was in working condition and had not mentioned the power adapter for it would not be provided, when I received the switch the po...
Hola, En la encuesta Final del curso, no me deja avanzae por la pregunta Num.7, Insiste que no hay respuesta y no permite avanzar para la entrega de mi certificado. Alguien sabe con quien puedo comunicarme o que puedo hacer?
Hello guys,We are currently have a built and operating DNA infra in our HQ, it consist of two Border control/border nodes and edge nodes serving endpoints in the fabric, Borders nodes are connected with 2 Fusion routers which is basically standard de...
we plan to migrate from CSSM On-PROM to smart proxy with DNA Center.Do you have any experience, suggestion, comment to share with me.Thank you for sharing your experience,
We plan to migrate from to CSSM on-premises model to the smart proxy model through DNA Center.I wanted to know if you have any experience with Smart Proxy in DNA and what changes need to be made on switches and routers?Thank you for sharing your expe...
In Catalyst Center (CC) on 2.3.5.5, when I create an AI RF profile, it has all 5GHz channels selected.In Australia, we have channels we flat out cannot use, such as 120, 124 and 128 as well as others than can only be used if the AP has DFS enabled, b...
I am syncing sites and devices between Cisco prime and DNA center. I have a particular site map and access points that have migrated over with the exception of one AP. Oddly enough, this AP does show does show up and registered to the wireless contro...
Dear All,I am working on adding two C9800-L-F-K9 (17.9.4a) in DNA Center (2.3.5.5-70026)I configured both WLC's to have Service Port (SP) done in its initial configuration wizard. RP ports are connected with direct cable run between both WLC. Configu...
Resolved! Cisco Catalyst Center AIR GAP
Hello, we have installed catalyst center in air gap mode and wish to verify it. I thought that only air gap installations have an "eula..."file and can verify it this way. But maybe there are better solutions. Kind regards, Daniel
Hi! I'm looking badly for Cisco Catalyst WS-C2960-8TC-L firmware.Corrupted one was c2960-lanbasek9-mz.122.50.se4Can you share it for me?Peter
Hello Community,I want to know any reference ( not to be stuck in theoritical parts to understand SDA ), to migrate from a Traditional Network to a Fabric Network. As in any document having SDA Deployement Process, or should I connect with the TAC En...
Hi all, we're attempting to upgrade our 9300 series switches but wondering what is the correct IOS bin for the C9300-48U model?https://software.cisco.com/download/home/286313806NAME: "Switch 1", DESCR: "C9300-48U"PID: C9300-48U , VID: V06 , ...
configuration to use external AD login has been configured.When enable external user is checked and a login attempt is made using AD account, it fails with invalid credentials. ISE tacacs live logs show a successful authentication and authorisation. ...
im trying to configure my switch, i got the initial part done, however tying to get the24 ports on 1 vlan i type the following command "interface range" reports back as incomplete command.typed interface ?and it shows that "range" is an acceptable co...
