Odd question, but how "Normal" is a Cisco server. Can we take an older DNAC and reuse as a windows server? There is a lot of RAM/CPU/SSDs in these to go to waste.
Forum Posts
DNACでインベントリ登録しているファブリック外(LANオートしてない機器)の機器で機器交換をする場合、RMAワークフローを実施しなくても機器交換は可能でしょうか？交換後の機器は交換前の機器と同じ設定を手動で投入想定となります。(接続するIFも同様) DNACのRMAワークフローを実施しなくても機器交換は実施可能な認識ですが、気にしているのはDNACで機器のシリアル番号も管理しているのでRMAワークフローを使用しない場合、その情報がどうなるかになります。デバイスの再同期等の実施により、その情報が...
Hi, I have a device recently discovered and when I am attempting to assign it to a site I can see a bunch of new configs to be deployed, is this normal? logging host 172.x.x.x transport udp port 514logging host 172.x.x.x transport udp port 514loggin...
Hello!When running the validation tool for Appliance Infrastructure Status i get a critical message with the following:Firmware version 4.3(2.240053) is not supported. RAID controller version 51.23.0-5009 is not supportedI just upgraded the CIMC firm...
HiI am testing migrating a subnet into SD Access. I have a subnet routed outside my fabric and I have a device inside my fabric on that subnet routed by the external gateway by handing off the address pool on a L2 VN. This all works fine.I now want...
Resolved! discovery vs pnp onboarding
Hi, I need to standardize our switch configs ( i.e. remove some acls, apply some new acls, delete snmp string, add new snmp strings, etc) and the devices in DNA center was added using discovery not PNP. do I need to onboard these devices first via PN...
Has anyone found a simple way to automate the deletion of old DNAC Backups?Our DNAC is set to backup to a Linux server each night, however, unless we remember to regularly go to the DNAC backup page and delete old backups the Linux server eventually ...
Hello, I have this issue with the IE3200. I can't reset through the reset button and I've tried through the CLI and I have this :Could someone know how to fix it ?
When getting events from this endpoint, how might one know when the event occurred as there does not appear to be a timestamp?https://developer.cisco.com/docs/dna-center/get-events/
Hello All,A customer is willing to buy DNA/Catalyst center with several C9200 & WLAN APs with Essentials subscription. customer is not willing to use advanced SDA features. He is just looking for a management platform for the switches and WLAN.The cu...
Is it possible to temporarily disable monitoring on a device that may need to go offline due to a planned outage or maintenance? I'm new to this community, so in advance thank you for any replies and input. - JD
Resolved! 2.3.5.6 Velocity Template issue
I'm trying to write a template to push AutoConf templates to ports and I'm having issues when I bind the input to the source. I have bound the $interface_range to the source, inventory, interface, portName when I run the simulation it never replaces ...
Hi Community,I'm trying to get Cisco's recommended approach on the placement of the DNAC Witness node in Azure for Disaster Recovery Implementation but could not find any document that covers this.Is the below plausible and supported deployment by C...
Hello,In my network, I have two Juniper switches that are connected by a Nexus switch that only acts as an L2 switch.I cannot learn the Mac-Address when I run Mac-Sec on Juniper switches on the Nexus side. (pic1)If I delete the Mac-Sec configuration ...
Hi,We have existing DNAC (v2.3.5.5) and there are existing devices already on board and assign to site using one CLI credentials.Recently we had deployed new 9200 switches on infrastructure and wanted to add or discover the devices. when we are tryin...
