Hi guys, I'm going to configure VXLAN on nexus N9K-C93108TC-EX but L2VNI no connectivity. Network topology diagram:https://prnt.sc/2346bcn At the all I used VLAN with EVPNtwo leaf switch can learn Mac addresses from each other through EVPN but L2VNI...
Forum Posts
compliments of the season Cisco community.I want to grant permission to any client outside, to access a tcp service on server within my LAN with IP 10.30.0.3I entered the instructions below but still can't access the service from outside. please can ...
How do I increase the number of mcast groups for feature vxlan. It looks like I can only get 128 out of it. This is the error the C9372PX is giving me. VDC-1 %$ %ICAM-2-SCALE_THRESHOLD_EXCEEDED_CRIT: Utilization of 114 percent for feature BGP Mcast g...
I need to perform a Port mirroring from a source in one Aruba HPE Switch, crossing other Aruba HPE switch and then ending in two Nexus switches.I know there is the option of RSPAN to perform Port mirroring between different devices in Cisco switches....
HiWe have a pair of Nexus 5k in VPC domain and these connect to a x2 stack switch through a vPC, the stack switch is already runnig BGP where we peer with ISPif I were to configure BGP Between nexus 1 & 2 and Stack Switch would I use ibgp or ebgp ??...
Hi Cisco Community,I am trying to enable openflow in nx-os 10.1 in 9300v... but i can't find the option "feature openflow". Does someone know how to enable that?
We need to know if the 9706 Multilayer Director Switch complies with the protocol SLAP: Switch Link Authentication Protocol
Resolved! Switch Link Authentication Protocol
Hello Experts,We need to know if the IBM Storage Networking 9706 Multilayer Director Switch complies with the protocol SLAP: Switch Link Authentication Protocol
Resolved! Adding a VLAN to a VPC
Hi! I am striving to add vlan10 to this VPC trunk. Here is what I have :int Po1swichport mode trunkswitchport trunk allowed vlan 8,9,10speed 10000vpc 10 On both switches. I just added Vlan 10 and it does not work. Any clue ?(or is it the BigIP right...
Hello,I want to setup L3 routed port-channel from Router to 9Ks that are vPC with each other and then run OSPF over them, so how can I do that? as far as two 9Ks has their own control plane, see below image.
Hi i am doing a battery count on site for EPCRA reporting and we have Cisco Catalyst 4500 on site. I am wondering if it has any battery in it?
Good morning I have some questions about the path to upgrade a pair of Nexus 7004/7006/7010 switches (presenting VDCs and single-homed FEX)Those Nexus today have the version 6.2.16 installed To reach the version 8.2.6 or 8.2.7a, should we go to the p...
Hi All We have a pair of N7Ks waiting to be upgraded. The N7Ks currently have single SUPs. We have ordered a pair of new SUPs . Not sure what the version of the IOS is in the new SUPs. What is the best way to get the new SUPs installed and N7K upgra...
Hello I've just faced an issue with mac address learning by an orphan port connect to a VPC node (N9k). I have dual side HSRP running on both: group 1 (SW1/SW2) and group 2 (7k-1/7k-1) in a particular vlan (10 in this example). Strange thing is that ...
Hello I hope some one can help. We have several MDS switches in a customer network, recently they had to add more IVR zones, but when the customer try to add one new IVR zone SAN12(config)# ivr zone nameIVR_mxoccsapcwd01_fcs2_new_MXOCCSTGSV1_SV2_N1P7...
