I have configured HSRP for High Availability but now from VPC I'm not able to reach vpc.Below is my routers and switch configuration. Thank youR1!!interface GigabitEthernet1ip dhcp client client-id ascii 9MGT16SBA3Jip address dhcpnegotiation autono m...
Hi Im testing a MPLS Pseudowire setup in which i would want the nearend attachment circuit to go down if the far end attachment circuit goes down. So far I've tested on a subinterface and when i shutdown the subinterface on the far end of the xconnec...
I understand that session hold time is for an established session, and the discovery hello intervals are for neighbor discoveries, but i do not understand why there is discovery hold time, while the new neighbors are being discovered in 5 sec interva...
Hi,I am working with the following topology: Between PE#1 and PE#2 an iBGP neighborship exists, both PEs have an OSPF neighborship with the P router. Recently, we've added a second physical link between P and PE#2 but we observed an uneven balanci...
Hello CommunityI was create a site to site VPN but it failed to come up for unknown reason. I kindly ask for help.I have two site. One is Site-A and Second is Site-B.At Site A I have NAT Host PC 10.1.1.10 to NAT 200.1.1.25 when I tried to initiate ic...
Hey guys, I got a problem.In the picture attached, R1 & R4 are running iBGP with 192.168.12.1, 192.168.34.4 and "next-hop-self" eabled. Now R6 wants to ping 5.5.5.5 which is R5's loopback0, and I know it would fail. Because the next-hop of 5.5.5.5 is...
Hello, I am trying to understand the use of 'mpls ldp password required' command. If I configure just the 'fallback' command but not the 'required' command ldp authentication still works. then what is the use of the 'required' command? Thanks,Sachin
can we build IPSEC between C9300 and Cisco ASR 1002? if not, any other options to configure data encryption with these hardware models using the mpls provider.
I'm trying to configure mVPN Profile 6.I am following a Cisco Live Lab by the letter and when I get to this stage: RP/0/0/CPU0:PE1#conf t RP/0/0/CPU0:PE1(config)#route-policy vrf-one-profile-6 RP/0/0/CPU0:PE1(config-rpl)#set core-tree mldp-inban...
I've been working on an MPLS/VRF lab and I'm a bit confused by MP-BGP address families. When I configured the PE to P routing (within the MPLS core), the BGP neighbors are configured under the VPNv4 address family, like this: address-family vpnv4 n...
HelloI know well if we have several paths to the destination, we will BGP Best Path Selection Algorithm . my question ,in which case we were obliged to use : BGP Best Path Selection Algorithm and and don't use anything else ?? i wait a answer fr...
ASR 900 line card 4 0 and 5 0 controller is installed but interface serial is not showing in asr router . Instead of this showing SERIAL-acr and serial-pg
HELLO ALLi have a packet loss issue in ISP domain from only one side in all PE routers which is CISCO NCS5K to ASR920 routers the issue only when pinging in NCS5K Type escape sequence to abort.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!...
Dear ,I’m trying to configure INTER-AS VPLS as the attached topology the ASBR1:Cisco IOS , PE1:ASR9K and ASBR2:Juniper MXThe L2vpn BGP Multi-hope BGP is up and I can see the label swapping form the both end but the VC is down RP/0/RSP0/CPU0:IGW-LON-1...
1. PPPoE Session on CE1:CE1#SHOW PPPOE SESSION1 client sessionUniq ID PPPoE RemMAC Port VT VA StateSID LocMAC VA-stN/A 0 0000.0000.0000 Fa0/0 Di1 N/A PADISNT0000.0000.0000```2. Interfaces on CE1:CE1#SHOW IP INT BRIInterface IP-Address OK? Method Stat...
