MPLS

Hi,There is a need to extend L2 connections from an existing 7600 with LAN cards to a new ASR9001 and configure IP address on that connection.To my understanding this looks something like "Pseudowire Headend".ASR9k:l2vpnxconnect group testp2p testint...

In a cluster of multiple route-reflector, is it necessary for the route-reflectors to be peers to each other? Does the use of the cluster id have any effect on this?

DearsI need your assistance please regarding A-VPLS core load-balanceAs I understood, A-VPLS inserts a new label "Flow Label" so that this label can be used in core routers to acheive load-balancing as shown in figure 2Now my questions 1- P router ha...

policy-map matchclass exp_0class exp_1class exp_2class exp_3class exp_4class exp_5class exp_6class exp_7class-map match-all exp_2match mpls experimental topmost 2 class-map match-all exp_3match mpls experimental topmost 3 class-map match-all exp_0mat...

hi,    we are facing problem with L2 MPLS VPN our scenerio is this that we are trying to connect our two branches through MPLS L2 VPN on our both sites we are using 3560 switches and Service Provider is using extreme networks switches and the service...

For MPLS netwrok, why it is necessary or recommended to have only "P" Routers on your main e.g: 10G linkWhy it is not recommended to have "PE" routers connected as part of Metro Ring??

Good morning, I have the scheme, including three devices: C7200, ASR9k, C7600. C7200 and ASR are in the same AS (iBGP-vpnv4 peers). ASR and C7600 - eBGP-vpnv4 peers. All relationships have been established. I can ping 7600 from ASR within vrf, but I ...

    Peer LDP Ident: 10.16.16.16:0; Local LDP Ident 10.15.15.15:0         TCP connection: 10.16.16.16.11013 - 10.15.15.15.646         State: Oper; Msgs sent/rcvd: 53/51; Downstream; Last TIB rev sent 74         Up time: 00:11:32; UID: 1; Peer Id 0...

Hi,I am trying to PoC MPLS multi path load sharing by using per-PE-per-VRF RDs in the network. I have a simple lab setup with AS65000 which consists of SITE1 PE1&PE2 routers (10.250.0.101 and 10.250.0.102), route reflector RR in the middle (10.250.0....

OK, as you can see got that error as well as these:*Aug  8 00:03:37: %MLSCEF-SP-4-FIB_EXCEPTION_THRESHOLD: Hardware CEF entry usage is at 95% capacity for MPLS protocol.*Aug  8 00:03:36: %MLSCEF-SP-STDBY-4-FIB_EXCEPTION_THRESHOLD: Hardware CEF entry ...

how ftn is programmed in mpls. i mean how ip traffic is put onto mpls lsp. can anyone tell how it is done in cisco routers

Hi All,I  understand that there are two types of EoMPLS, VLAN based (VC type 4)  and port based (VC type 5). However, I am a little confused on the  configuration and the show command output on the router.First TestI tried to configure port based EoM...

Hello, I have exiting Cisco 7600 in 4 location and bandwidth in 300 mbps. The sites are connected as ring so that we can achieve failover. now my organization is coming with additional 450 MBPS link on that same router. So please can anyone tell me h...

Hi All,I understand that there are two types of EoMPLS, VLAN based (VC type 4) and port based (VC type 5). However, I am a little confused on the configuration and the show command output on the router.I tried to configure port based EoMPLS using bel...