hi, i'm having a issue with show users on a cisco catalyst 3750i'm logging in with a local user and I have tried logging in with a tacacs and radius account, when I do a show users on the switch it doesn't show the username,however on the cisco 1841 ...
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
Forum Posts
Hello All,We have a failover pair of Cisco ASA VE running 9.14 and have an issue polling for SNMP. The client device gets no answer, and tracing on the ASA shows the packet arriving and being un-nat from the inside interface to nlp_int_tap interface,...
Resolved! Ise PAN Question
HiIf I need to promote my Sec PAN to Primary PAN due to the PRI PAN being stuck in initilizing, does the promotion cause the ise restart on all nodes or just the Sec PAN Node.?? Thanks
So i run a hotspot guest portal with it's proper SSID, but WLAN and guest portal are on separate networks.So guest WLAN is on let's say 10.10.10.0/24 and the guest portal is on 10.20.20.0/24Have Webauth redirect configured and working fine, together ...
We are having an odd issue with newer versions of Iphone/IOS when try to access the ISE Guest Portal.The users start the CWA flow, connect to the SSID then gets an username and pass provided by cisco ISE, then login using the provided credentials and...
Resolved! ISE integration with cisco DNA
Dears, I need to understand which certificates are used between ISE and DNA, and if I do not have an internal CA how I can use the signed certificate and the DNA
Resolved! IP Device Tracking
Hi guys. I want to find out about the usage of device tracking feature on Cisco switches.When we use that?
Hi, I have a "C1000-16FP-2G-L (15.2(7)E9)" device, I have enabled automatic config archive creation, but it gives the wrong time when naming. For example: While the time of my device is "10:15:19.801 +3 Thu Feb 8 2024", the name written in the archiv...
Resolved! ISE deployment
Hi all, Does Cisco ISE need L3 dependency in deployment. Please give me some details ok it.
Hello everyone, We actually use an ISE (version 3.1) to authenticate endpoints in wifi using a certificate.The configuration is pretty simple but now we want to allow authentication for internal users (created and stored in the ISE) Problem is, the ...
Hi All,We are facing issue in Windows 11 to authenticate with Cisco ISE 3.1 using EAP-TLS. Same issue was in ISE 2.6. Then we upgraded but issue was not fixed. No any connect or posture modules are in use. Simple EAP-TLS authentication we are trying...
Good afternoon,Does anyone know of way to configure a timeout or time limit for an endpoint to be in a Pending or Posture Unknown state?We are concerned about credential theft and unauthorized devices remaining in this state with access.Thank you
Good Afternoon,We are trying to implement ISE posture enforcement by referencing an ACL in our Authorization Profile. We have this working on our WLC operating in Local Mode.In another branch location an affiliate company we partner with controls th...
Resolved! failed backup repo?
Hello, I have ISe 3595 v2.7. I am trying to make sure my backup with TFTP is correctly backedup. DEVC-ISE-01/admin# show repository TFTPRepoWhen i do show repo I get what looks like to be a error but I am not sure. The backups did appear in the fol...
I have two ise nodes one prim and one backup. I deregistered the second node because it was not sycning and when I go to register it I get this: Unable to authenticate ISE ISE-02. Please check certificate configuration.Make sure from 'Primary Admin n...
