I was wondering if when upgrading from 8.2 to 8.4 if the NAT rules will be automaticlly rewritten to the correct values during the reload?If not does anyone know of a migration tool that can be used to do this? I could do it manually but there are q...
Hai,I have faced an issue for accessing my ASA 5550 via http. I configured http server enable and the required access for the firewall.I have configured firewall in mode multiple, in which i have one admin context , where the management interface is ...
Hi All,Just doing some basic testing before we replace our ancient PIX 515E with a new 5512. I have a mini lab set up following the diagram below, although I am unable to telnet through to the mail server's netcat listener on port 25 TCP. I can ping ...
i want to allow a server on my Internal to communicate with a server on my dmz over a specific port (i.e 5555) and vice versa, from outside i can connect to the dmz server over https. here is my config, i have only replaced the ips with dumy ip's. i ...
Hi,Recently, I unable to configure the failover on bridge group in transparent mode . I have five interfaces .out of this only 3 is showing in the show run config .can you please confirm whether I can config failover on on of the data interfaces.I ha...
Hello Guys, Please, I need to create a static NAT in order to allow a specific host(source) on internet (ex: 100.100.100.100) to connect a specific internal host (ex: 10.10.10.10) for a video-conference system. My question is : h...
I am not sure if NAT is the solution, but here is my problem:For a test lab I have the following setup: (The IP's are in 192.168.49.x range and subnetted as /29)Landing server(192.168.49.26)---(192.168.49.25/29)-[[Cisco6500]]-(49.1/29)---(49.2)Cisco ...
IOS IPS customers running version 12.4T, 15.0M, or 15.1M - a critical software defect has been identified which may cause your router to reload and be stuck in a boot loop if IOS IPS signature version S639 or later is installed on the device. Recove...
I'm just starting off on ASA's and i'm out of ideas here with this problem. I simply want to be able to ping from inside to dmz and vice versa. At this time i don't have any servers in the dmz except for the dmz interface which is 172.16.100.254, my ...
I'm going through the Cisco CCNA Security Lab manual and in Chapter 9 I need to use the security policy builder. The link has since been deprecated (www.ciscowebtools.com/spb). Does anyone know where I can still find this tool or if maybe it has been...
Before upgrading to 8.4(4)1 I was able to ping our inside interface accross the VPN. Now I cannot. Because ping is not working, my SNMP server thinks that the device is offline however I know the VPN tunnel is still up and the remote branch office ...
Are the ASA memory DIMMs created for specific models? Would a 1GB 5510 Memory stick work in a 5520?Thanks.J
I am very interested in tuning my ASA Threat-Detection configuration. I desire for the device to shun addresses quicker for ACL failures and IP scanning. Any advice would be most appreciated.
Hi all, I have a quick question, I like to set up a pix and router for this network for a small buss, but I need to know what type of cable do I need to set this connection to work straight through or a cross over cable? also I need a subgestion if...
Hi,I recently upgraded to ASA 8.2, but when I try to connect from the windows desktop ASDM I get the error ' Your ASA image has a version number 8.2(5) which is not supported by ASDM 5.2(4).I installed the ASDM from version adsm-demo-649.msi which cl...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-25-2025 04:32 PM | ||
| 06-25-2025 04:40 AM | ||
| 06-24-2025 07:03 PM | ||
| 06-20-2025 07:10 AM | ||
| 06-19-2025 07:32 AM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 4 | |
| 2 | |
| 1 |
