Buy or Renew
Buy or Renew
NEW! Stay up-to-date on Cisco Secure Access: Software Release Notes and Announcements

Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Free

 
Labels

Forum Posts

Start a conversation

Resolved! ASA NAT Exemption

I'm running ASA software 8.4(2)I've setup the anyconnect VPN system, and it works fine. However, it's NATing to the inside interface of the ASA. How do I do the NAT exclude ?The docs say you *used* to do:access-list no_nat permit ip 192.168.0.0 255.2...

Resolved! Unable to copy to ASA flash

I was trying to upgrade from 8.3.1 to 8.3.2. but I am unable to copy via tftp to the ASA flash or disk0:ASA5520# copy tftp: flash:Address or name of remote host []? 10.88.127.153Source filename []? asa831-k8.binDestination filename [asa831-k8.bin]?Ac...

jennyjohn by • Level 1
  • 3771 Views
  • 12 replies
  • 0 Helpful votes

Resolved! snp_drop_none

Hi,What does this message on the end of the logged line mean?Aug 18 2011 13:16:55: %ASA-6-302014: Teardown TCP connection 37247 for outside:192.168.26.125/3618 to inside:172.26.1.5/18082 duration 0:00:00 bytes 0 <snp_drop_none>ASA 5505 v8.4(2). Thank...

lcaruso by • Level 6
  • 6090 Views
  • 2 replies
  • 0 Helpful votes

ASA 5505 losing outside interface

Hi all, I have a problem where my outside interface stops passing traffic and the only way to resolve the issue is to reload the ASA, the interface never is down it just stops passing traffic.The inside interface never stops allowing traffic to pass ...

martynch1 by • Level 1
  • 1774 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Add remark using CLI to ASA

Hello,I'm faily new to the CLI world of the ASA. 1.)   I've just added an access rule, but how do I add a remark to this access rule?  Do I need to find the line it exists on?2.)   How do I insert a rule before another using CLI?Thanks

Looking for a right solution

Hello, Looking to replace an "all-in-one" type firewall (UTM/Firewall, SSL VPN) with a cisco product - the issue i'm running into is that we have multiple ISPs plus WAN and DMZ - overall more than 5 ports on mid-range ASA devices - and from what i re...

captkloss by • Level 1
  • 563 Views
  • 2 replies
  • 0 Helpful votes

Deny inbound protocol 41

Recently I've started getting absolutely hundreds of protocol 41 deny alarms on my ASA firewall outside interface. These are flooding my syslog and making it hard to check for other issues that may be going on in our network.Most are from 94.245.121....

handsy by • Level 1
  • 8441 Views
  • 3 replies
  • 0 Helpful votes

Transparent Mode NAT

I have a transparent firewall (ASA) running 8.4 in a 10.1.0.0/24 subnet and I need to NAT anything entering the inside interface with a 10.x.x.x address to 192.168.1.2.. please can someone tell me the code to do thisThanks

lquin1978 by • Level 1
  • 1996 Views
  • 3 replies
  • 0 Helpful votes

internet routing

Dear SirsWe would like to configure some internet access route through remote site ISP gateway by using IPSec VPN tunnel. For the rest internet traffic keep using local ISP? Would you please teach me how to configure it?Hugo

Botnet filter question

Just fired up the botnet filter service on one of my ASA's today.  Seeing traffic that is tripping syslog message 338001 and 338002 where the recommended action is to use the dynamic-filter drop blacklist command.When I try to use this command, I get...

View All
Review Cisco Networking for a $25 gift card