Network Security

Hi Folks,Our PIX 515E version 6.3(4) is not logging to syslog for all events except for the events which are generated due to Admin priv access.We've configured following:-Logging onlogging timestamplogging trap notificationslogging host interface Sy...

Hi,Consider scenario :-Host A--->Router B--->Router C All are in the same subnetRouter C also has an active interface on another subnet.When I telnet from A to C (interface with ip address in another subnet),I force traffic from A to C to pass throug...

Hi,Execuse me, I am new to FWSM but I already have good experience with ASA; I have a deployment for FWSM as follows and I need to consult with you on certain points:A- The requirement is to create two contexts "FWA" and "FWB" alongwithAdmin Context ...

I was able to access Cisco IDS 4215 v4.1 at work (production device) through WebUI, and Telnet.Recently I have modified the interfaces int0, int1 only, then I could not access through WebUI nor Telnet.When I tried through Telnet I received this error...

I'm upgrading my test lab PIX from a 520 to a 515E so I can run v7.x OS; are the 10/100 PCI interface cards compatible from one model to the other?For that matter, can I salvage the RAM from one to the other, also?Thanks,Marc

Hello, I have a cisco PIX 515 with 16Mo FLASH and 64 Mo Memory.I want to increase Memory and FLASH on it.So I have seen there is a part Number PIX-515-MEM-128 to do this ( 64 to 128)I understand this is going to increase the memory (64Mo to 128Mo), b...

We have two PIX firewalls (FO-UR licenses). The details are as below:Cisco PIX Firewall Version 6.3(5)Cisco PIX Device Manager Version 3.0(4)Hardware: PIX-535, 1024 MB RAM, CPU Pentium III 1000 MHzFlash i28F640J5 @ 0x300, 16MBBIOS Flash DA28F320J5 ...

Iam trying to connect to client server tho' GVC client. But I fail to connect and getting error message %PIX-3-305006: regular translation creation failed for protocol 50 src inside:xxxx dst outside:xxxxI have conigured PAT for Internet access and do...

Hi,First off this is my first Site 2 site I have setup from start to finish. I want to setup tunnel with a client to access there mainframe. My inside addresses allowed thur will be 192.168.x.x/29, and access 2 IP on the clients side. In PDM I cre...

Does anyone know something concerning to the following issues?Please teach me what I can refer to on the WEB,if possible.1. Is there any way to apply the policy(checking OS/AV) to the kind of client devices which CAA hadn't been installed such like g...

Can I redirect traffic coming from the Internet to different internal devices based on the source IP of the Internet user with an ASA5510, (for the same service)?For example, if I have 2 web servers with inside IP addresses 192.168.10.10 and 192.168....

I need a way to monitor router interfaces status with history records.I configure the router snmp-server trap-source f0/0snmp-server host 172.17.1.26is there any option that can help me to monitor all the sites router interfaces.I'm also using wt's u...

I'm seeing exceed MSS errors for Cisco remote access and tunnel VPNs passing through or terminating at ASA 5510 (7.2.2).I have found documentation to set to ignore MSS via a map class, but I'm confused: aren't cisco VPNs compliant with Cisco ASA rul...

hi, am having trouble configuring a 506e firwall which is currently setup in a lab, i think there is a problem with the acl's or the static routing but not sure so here is the config.thanksAlex