Hello Everyone,It may very well be the time of day I'm writing this and long hours of looking at the screen.. but I'm setting up a lab ASA with an inside and outside interface. Inside interface is connected to a L3 Nexus 3064 using a transit VLAN ( 1...
Forum Posts
HelloWe want to integrate Firepower with ISE via pxGrid.We do not have a internal CA server so we want to use ISE as internal CA with local self-sign certs.As far as I know on Firepower I need to generate a CSR so it will be signed by CA (Cisco ISE) ...
Hello, I am trying to figure what would be the ASA configuration that could do the same thing this watchguard does, I need the configuration.that Fa0/0 carries vlan 10, 20 ,30 and they are just vlans, fa0/0 interface is probably a router on stick so ...
Cisco ASA Interface are connected to Cisco 3560 switch Cisco ASA Gig 1/1 = Cisco 3560 Switch Gig 0/1Cisco ASA Gig 1/2 = Cisco 3560 Switch Gig 0/2 ********************Cisco ASA Configuration******************** interface port-channel 1nameif insidese...
Hi we have a cisco asa5585-x firewall and it is crashing twice per week and it is generating crash dumps.can somebody help please?ASA-SSL-VPN-III# show versionCisco Adaptive Security Appliance Software Version 9.6(4)12Device Manager Version 7.9(2)152...
If filtering were to stop working for whatever reason, will the ASA fail to a secure state? How can I verify this?
Resolved! Latest Starred version 6.4.0.4
I'm currently running vFMC and FTD 2130 version 6.2.3.13Could someone please confirm if i can upgrade directly from the 6.2.3.x version to the latest 6.4.0.4 version.
Resolved! Firepower Management Center
Hi,Can i safely shut down the FMC server? I have two Firepower devices connected to this server. Is there a description of what data they exchange other than policies upon request?
Our system has installed Cisco ASA 5525 X firewall with active-standby setting. We would now like to procure the FirePOWER service and deploy on the existsing firewall. However, we have concern what if the ASA firewall behave if the FirePOWER service...
How do I go about configuring the crypto map for an IKEv2 VPN, on a remote office, which connects back to an ASA behind an edge router with 3 multihomed links?I've read lots saying that each of the 3 addresses could be added to the 'set peer' command...
I have (had) a cisco asa 5506x which died last night due to the field notice FN - 64228 (clock signal component error). I would like to buy a new one but unfortunately I don't have a copy of the running configuration. Is it possible to retrieve that ...
Hello We configure a RAVPN solution using Firepower 2110 v6.2.2.10 managed via FMC.The AnyConnect establishe a connection but after 30min the user gets disconnected and the next message appears..."The secure gateway has terminated the VPN connection....
Looking to do PBR on the ASA for Tunnel interface, is this possible? It has been super long time since I have done this because I try to avoid it at all costs. I cant recall when I make a PBR ACL that uses a source Subnet to a destination subnet on ...
Hi everyone! I have the next error in the SMTP configuring the SMTP client on FMC to send e-mails, the FMC is 6.2 and the relay works perfect from Windows (almost 50 devices syncing mails in & out), but FMC configured the same way: mail sever: <IP_ad...
Hii'm working on a asa 2140 and am having trouble configuring etherchannel in asa mode on interfaces 1/13 & 1/14. I enabled and configured the interfaces for 1gbps in fxos prior to setting up an etherchannel, & issued commit-buffer command. After i ...
