Does anyone know where you can download a copy of Cisco Transport Planner? I need to open a project file to review the design but cannot find the software available for download anywhere. Any help would be appreciated.
Hi,ON ONS DWDM CTC, I can get the utilization on card view -> Performance -> Payload PM ->Utilization.But for the line card MXP_MR_10DME, it does not have utilization mib (SNMP). it has RMON mib.My question is How to calculate the Fiber Channel ut...
Kindly check diagram..is it working in live environment?two buildings connected with Single mode OFC...on both side LIU SC Connector (Single mode) -- On both end we have to connect Router/ Firewall - both have Multimode SFPs.
Hi, we are considering to interconnect two sites using DWDM. What type (colored, non-colored 1310) SFP modules should we use on our switches connecting to multiplexer/OADM? Does it depend on the actual MUX device?
Hi,I have 2 ws-g5484 and 2x 3550. Each SW has 1 ws-g5484.The switches are conencted via ws-g5484'sThe first one's link status is up/up.The second one is down/down.If i change the GBIC's position in that case the first switch's interface will be down ...
HelloRecently my data center 3900 series router had the above SFP go bad. Becasue of this problem, mycarrier thought it was somethingin their network. They replaced the optical card and we were still down.Is there a way to configue an SLA on the devi...
Hi,At End A we have an STM-1 connectivity, wherein we have created E1 channel. and other end has been connected with 2Mb modem.All Links connecting to the same STM is working fine, expect one channel.It is showing as Serial0/3/0.1/1/6/3:0 is down, li...
Hi all,I'm running on cisco 3750E series switch stack and getting following errors in log "SFF8472-5-THRESHOLD_VIOLATION: Gi2/1/2: Rx power low warning; Operating value: -19.4 dBm, Threshold value: -17.0 dBm"There are two ports in this module and oth...
Hi,Can anyone advise where can I download the data sheet of Cisco 10G SFP+ with DOM? I was able to find one but it doesn't include the details of Digital Optical Monitoring (DOM). Unlike in 100Base SFP and 1000Base SFP data sheet, it includes the inf...
Hey everyone-I am a little newer with configuring switches and routers, and I have been asked to troubleshoot a FET-10G-SR in our NEXUS 5548 and NEXUS 2248. I am aware that the ports need to be configured to except FET parts, and I have tried using ...
Hi,I was wondering that I'm not able to get transceiver details on a c6500 (with sup720-bxl) platform running version 15.1(1)SY1.Xenpaks will do fine:c6504#sh int Te3/3 transceiver
ITU Channel not available (Wavelength not available),Tran...
Hi,We are looking for fiber-to-ethernet converter.Is there any SFP module that plugs directly into the Fast Ethernet port of any switch.Please go through the following link:-http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6578/product_dat...
Hi, everybody.Soon i will implement RAMAN-COP, and i woud like manualy calculate raman link to understand how it's work. I have CTP design of A and B stes. On witch site SMR-1, AMP-C and RAMAN-CTP. CTP calculate paramentrs on each site:- SMR-1, LINE-...
Dear community,I am encountering a strange problem on a customer premises. I installed the CPO 9.6.3 on a HP DL380G5 without any issue as a test System. All was working fine, I could create documentation...Now at customer site I expected to get the i...
