Ask Me Anything Event Thank you for joining us for the Expert Insights Series on ACI & NDI: Empowering Data Center Excellence! Our Customer Success Specialists Cody Albea, Peter Nalley and Manuel Valasco will be available from May 15, 2025 throug...
Forum Posts
Dears, We have installed RPS 2300 devices on our Data Center during the maintenance window we have connected different devices to the RPSs. Everything is working, and we were able to check the connected RPSs using "show inventory" command. After ...
Hi, I would like to check if the Nexus 9372PX supports VDC? I happen to check out the cli for a nexus 9372PX and it seems vdc commands are available, but tried to look on documentations and it seems Nexus 9000 does not support vdc. have not tried ...
As titled. Can't find any documentation confirming whether is or not. Datasheet says nothing about it.
Hello community, I am concerned because I am new in a job and I realized that they have configured dell servers with 2 x 10Gbit cards and ESXi 6.5, those servers have links to each 6509 catalyst VSS switches. interface 1 ESXi > TenG 1/1/2 interface ...
I have a FC link on two Nexus 5000s hard set to 4gig but the speed seems limited to approx 300 Mbps. Any obvious reasons?
Hi guys, I am on my way of replacing two classy IOS HSRP enabled core SWs with two Nexus 9372. I vPC on both along with vPC peer link and vPC peer-keepalive link. Next I connected all uplinks from access switches (pure L2 SWs) to each Nexus and use...
Hi all, Per default PTPv2 works in NEXUS 9K when is enabled but my device "Standard Dante" only support PTPv1. Can be enable PTPv1 in CISCO NEXUS 9k? What's the command? Clocking Notices AES67 mode on a Dante device enables both IEEE 1588 Precisi...
Recently, i found a MCS 7825-h3 closely to the garbage.I wonder if can format and install windows for gaming design purposes??Greetings!!
Hi! Recently we found native vlan misconfiguration on vPC Po trunk links: two double sided vPC Po between two VDCs within a pair of Nex7,7kone double sided vPC Po between a pair of Nex5,5k & pair of Nex7,7k We got a task to clear this problem. I took...
I see APIC is a C220, is it possible re-image it or change it to be a normal C220 then to run ESXi?Thanks,
Hi Team, Is Cisco KTN expired or out of service ?I don't find any related configuration document for Cisco KTNRegards Prashan
Hi All, Please could you help clarify something on the uplink ports on the Nexus 92160YC-X model? According to: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/hw/n92160ycx_hig/guide/b_n92160ycx_nxos_mode_hardware_install_gui...
Resolved! L2 NetFlow on N5K-C5696Q 7.3(2)N1(1)
Hello! I have setup L2 NetFlow on a Nexus 5696Q running 7.3(2)N1(1) code as follows: feature netflow ! flow exporter mac-netflow-export destination 172.28.0.254 use-vrf management transport udp 2055 version 9 !sampler mac-netflow-sampler mo...
Community, I have a pair of 9396PX's running NX OS version 7.0(3)I4(6) that have two port channels between them. Po1 is the vPC peer link that carries most of the traffic between the two switches in vPC domain 1. Po2 is a "routing backbone" links t...
Hello We have two NX5600 7.1.4 in our network. We run VPC between them and enable peer-switch. We have stacked two 3850 and connected them to N5600s with 4 link (full mesh). We have used 1 port-channel for connectivity of 5ks and 3850. Should we ...
