Other Data Center Subjects

I need help setting up ASA 5506 X for the first time. My network is very simple Out side network  router (192.168.10.x/24)  <<<<< outflow traffic   ASA 5506 -X <<<<<< Internal network (10.10.50.x) Can someone guide me how to do initial basic setup ...

Hello All, I'm working on OSPF configuration and I have query on setting the MTU over the L2 path between L3 endpoints. Topology: Firewall(L3 SVI with an MTU of 1500 bytes) <=> Nexus 9K (L2 trunk with and MTU of 9000 buytes) <=> Nexus 9K (L2 trunk ...

Hi Folks,I am getting below error while trying to create VDC. As per my knowledge by default 4 VDC's are allowed without VDC license.CS7009-A(config)# vdc ProductionERROR: VDC create failed: License restrictions precludes further vdc creationCS7009-A...

New installation (and I'm new on the N9500s).......Attempting to do some failover testing before going into production. When I commanded a "system switchover" from active SUP to backup SUP, switchover occurred, but what was the primary SUP now shows ...

Hi, we have an upcoming dual 4500E Sup8-E installation in Easy VSS the os that is being shipped is with ip base licensing - IOS XE - cat4500es8-universalk9.SPA.03.08.00.E.152-4.E.bin http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/rele...

there are 2 Nexus7K(2 as vPC+) as well 2 Nexus5K(2 as vPC+) . These  switches be connected via fabricpath.i'  ( see attached file )  and i'm running ospf on vlan 200 and vlan 200 mode is fabricpath  use " layer3 peer-router " on VPC+ in pair 7k and r...

Anyone know when 7.0(3)I4(6) will be released for Nexus 9k? We are running into two software bugs that are affecting Nexus 9k and the bugs are marked as fixed in 7.0(3)I4(6), but I don't see the code available CCO. Thanks, https://bst.cloudapps.cisc...

I have Nexus 9500s and 9300s. VPC enabled. A router below is dual-homed to the 9300s. I would like to establish IGP adjacency as below. Is this a supported topology? How will be the behavior of OSPF neighbors, failover in this case? Please advise, th...

HI All, Just want to confirm if any effect or bad configuration if the Service Instance in Overlay Interface and Lan Interface is not same? interface Overlay1no ip addressshutdownotv control-group 225.0.0.1otv data-group 232.10.10.0/24otv join-inte...

UCS C210 M2 : Physical Disk in Yellow Color from Megaraid wizard View 1 Disk : Show solid Amber Color   Solution : Replaced it with new disk and rebuilt it using megaraid Wizard View. 2 Disk : show Blinking Amber Color on LED and Physical Disk is ye...

I am planning to configure OTV in ASR1001X router and during my research I found this article. "The current OTV implementation on the Nexus 7000 enforces the separation between SVI routing and OTV encapsulation for a given VLAN. This separation can ...

Hello, I have a customer using a Cisco collector, and they have noticed their N9Ks' host names are being cut off after 32 characters. I found several bug IDs that are similar to this issue but all are for older versions of OS, they are running 7.0(3...

Dear, I just started a QoS implementation project at customer premises. The following switches are in the path: Nexus 93108TC-EX and Nexus 93180YC-EX. But I don't find any QoS information for these Nexus 9300-EX family. What I need to know is: - is Q...

when i try to install dcnm 10.1(1.123) in windows 2012R2 , am getting Following orhpan services detected error I have deleted Zero D and Cisco Systems folder.In Serivices, CISCO SMIS Agent is stopped. but still issue exists.   coul you help me pleas...