Other Network Architecture Subjects

I have a VMWARE server and it was connected to the network using IGMP Multicast. The server is running MS Windows 2003. I have to add an ARP entry for the server. When I do a show arp I get no VLAN for that device. All the other VMWare servers are ru...

I have connected a Network Intrusion Detection device up to our server subnet and have basically swamped the IDS device. I know you can have multiple SPAN statements in the 6509 config, but how many can you have? Also, can you have multiple devices...

I've some problems on my 6500 I think that could be happened a switchower event with all modules resets... but I do not understand why...After the resets the active supervisor is the second, and all works fine...I post the sh techThanks allG.

Hello, When applying an access-list like this:access-list 11 remark TESTaccess-list 11 permit 10.10.10.1access-list 11 permit 10.10.10.2access-list 11 permit 10.10.10.3access-list 11 permit 10.10.10.4access-list 11 permit 10.10.11.0 0.0.0.255access-l...

trying to configure an internal DNS Server running off a Dell blade.added config to PIX:alias (inside) 67.39.116.149 192.168.1.214 255.255.255.255static (inside,outside) 67.39.116.149 192.168.1.214 netmask 255.255.255.255 0 0 access-list outside_acce...

HiThat say I have 3 router and I want to enable RIP routing protocol. Do I have to configure RIP on all 3 router ?PLs advice. THanks in advance..

we are installing a replacement web server. the new server is running off a Dell blade. we want to route the public address to a 1. address. currently, it is routed to the DMZ.the problem is when we attempt to access the server internally via doma...

I have a PIX firewall 515e (all workstation default gateway), Cisco 3000 Concentrator(VPN Site-to-Site Tunnel), Cisco 2600 Router(Internet Gateway). I have problem when LAN workstations are using Firewall as default gateway, they are not able to get ...

I have a single VTP domain with over 30 VLANs; I was asked to isolate an unused VLAN from all VTP L3 switching in the core switch (a 6500) for MS Active Directory domain testing that cannot interfere with the production domain.I'd like to verify whet...

Hello,what i am looking for is to configure on the physical atm interface ppp athentication without using dialer profiles. This config is needed in order to oer border router participation in oer master controller decission process.I post the working...

trying to reboot from ATA but fails with disk reading error.I have the following boot statements;boot system flash disk0:rsp-jsv-mz.123-12a.binboot system flash slot1:rsp-jsv-mz[1].122-26.binsh version gives Chassis Interface.1 CIP2 controller (2 IBM...

Hi,I'm familiar with configuring several, shall we say, "lesser" routers to ADSL lines. Our ISP normally provides 8 IP addresses, and the "lesser" routers are normally configured in "half bridged" mode (i.e. the router just passes any traffic destin...

I am trying to make 2 2620's connect with MLPPP. The problem I am having is that 1 of the WIC interfaces goes into alarm mode after boot up.When I boot up the router the second WIC will go into alarm mode and not pass traffic. If I then shut down t...

I am new to the LAN world, and I am learning all about configuring Cisco routers. My question is why would you want to use BGP on your external connections, and OSPF on your internal connections when BGP interior seems to take care of all internal c...

Good Afternoon,I would like to know if anyone knows a process to configure a virtual-mac address in a token ring environment.I can't use HRSP for Token Ring becouse the mac address i am trying to deploy isn't a functional one.