Dear all,I am having 3662 series router. It is running OSPF and BGP. It is running 1 E1 link and some clients.Its components are as follows.Flash:16 MBRAM:2 in no. 64 MB eachIOS:16 MBIt hangs once in a day daily.Regards,Tushar Garg.
How can I add my ACS server to HPOV NNM v6.41 (Win32)so as to monitor its availability?I have tried to do this but NNM is showing the ACS in red as unavailable. Also there doesn't appear to be a place within ACS to allow it be monitored from an NMS ...
Hi we have a problem on 4 switch/router 6509 which are at 100% CPU due to the process llcSSTPFlood.No documentation on that process on the web, is this already happen to you. Do you have any documentation?Regards,Frédéric
Please suggest: I have to establish connectivity between two sites. We ahve a IPL Circuit between the two sites. On, site 1, users are on 10.111.0.1 subnet and WAN link is 10.222.0.1. On site 2, WAN link is 10.222.0.2 and LAN is on 192.168.40.0. Plea...
We have a network installed in a large serviced apartment (305 rooms) utilizing a BBSM v5.3 connected to a WS-C3550-12T as a core switch and then connecting to 7 2950T switches then connecting to Linksys WAP54G access points to provide internet acces...
Hi All,I understand how to NAT on a Checkpoint Firewall, but am not sure how to do this on a router.I'd like to translate anything with a source address of a.a.a.a, going to a detination of b.b.b.b, to have it's source addess translated to c.c.c.c, a...
Hi, I was just going thru a documentation abt disabling vlan 1 on trunks,I came across the following lines..."On the Catalyst enterprise LAN switches, VLAN 1 is enabled by default to allow control protocols to transmit and receive packets across th...
Hi , im have trouble:my router hangs regularly. Fact Cisco 2611XM router:-----------------C2611>sh verCisco Internetwork Operating System SoftwareIOS (tm) C2600 Software (C2600-I-M), Version 12.3(6), RELEASE SOFTWARE (fc3)Copyright (c) 1986-2004 by c...
Hi , I have to configure two Cisco routers , working with tunnel interfaces for GRE encapsulation over IPSec.One of the routers , has two external interface's IPs , the second only one interface.How to configure both routers to work with different IP...
I have a router 1721, where I have configured subinterfaces to allow inter-vlan routing. It´s working fine. I need to replace this router for a 1720, and when I type encapsulation type I get the message: unrecognized command.Does 1720 support inter v...
Hi,We currently have OC12 connection in our network, and we are thinking of replacing OC12 with Gigabit ethernet connection.Is there any drawback switching OC12 to gigabit ethernet connection? Would gigabit ethernet connection perform well as OC12?Th...
Hi , I want to set web proxy use wccp on my CAT 4507R with Sup-4 but my CAT 4507R don't support it then I used Policy Base Routing to route web traffice (tcp port 80,443)to my squid server ,it's seem ok but my network was very slow and when I use com...
Hi,I'm studying for my CCNP and I got a basic question on frame relay and ATM .What is the exact difference between both protocols ? In the bcran study guide they say that a lot of times you have a frame relay switch and that afterwards the packet i...
hi!I'm having problem how inbound/outbound should be used in access-list. Can anyone help to explain?If i'm configuring subinterfaces on a router. The access-list applied should be inbound if all the filtering is within that phsysical interface. Am i...
