Hi Guys, Which console can be used on this router? On CCW Cisco suggest this console: CAB-CON-USBRJ45 Below is the console interface
Forum Posts
Listen here: S11|E13 Master Network Analytics, Assurance and Security with Intelligent Capture Packet captures are an invaluable tool for network teams, yet the traditional process of capturing can be manual and cumbersome, turning what should be an ...
Listen here: S11|E11 Cisco Validated Delivers Value Part II Did you notice that Cisco Validated is now at the center of Cisco.com? Do you have the responsibility to prepare, plan, design, implement, integrate, secure, and operate IT infrastructure? I...
After EOL of most devices, will the new devices all change to SDAccess and SDWan? will campus network devices be deprecated that force whole world change to SDAccess and SDWan?will spanning tree , multiple spanning tree , VPC, load balancing mac dest...
I have the following configuration on a Cisco 9300 : interface TenGigabitEthernet1/1/1switchport access vlan XXswitchport mode access!interface TenGigabitEthernet1/1/2switchport access vlan XXswitchport mode access!I have two PCs connected to those i...
Hi AllI have cisco ISR4431/K9 router logs below. what is cause root for the following notifications?024719: Nov 7 09:42:23: %IOSXE_QFP-2-LOAD_RECOVER: Slot: 0, QFP:0, Load 29% recovered.024720: Nov 7 09:42:38: %IOSXE_QFP-2-LOAD_EXCEED: Slot: 0, QFP:0...
I replaced our home Netgear router with this Cisco unit, and it is behind the AT&T gateway.The Cisco has all ports on VLAN1 in Trunk mode using overload to port 8, and it's performing well, except I'm having trouble with some of our smart devices sin...
Bonjour,Je précise que je suis débutant. Comment est ce possible de lancer un ping depuis un switch sachant que le switch est de niveau 2 et ne construit que des trames de niveau 2 avec la mac source et la mac destination. Du coup il manquera l'ip s...
Resolved! How to connect DC core to Campus core?
Hi, my question is about connecting DC core to Campus core. For example, there is DC core which consists of pair of Nexus Switches, and Campus core which consists of pair of stacked Catalyst switches how should they be connected to each other, should...
In some games, they show a Bar representing the connection...it's usually betwen 1-4 bars, 4 being the best. Well when it fluctuates and goes down to 1, is it because of a "Layer 1" problem?
I am having a little situation here; for some reason I can get my switches and routers to display the dhcp relay even though it shows to be configured on the network's vlan. For example, when I entered the following command; SW# sh ip dhcp relay info...
Hi,I would like to understand the meaning of the number appended to the filename at the output of a show bootvar. ,1 or ,12. I could not find a definitve statement at the cco. Can anybody help ?Switch>sh bootvarBOOT variable = bootflash:cat4000-is-m...
Resolved! L3 Switch with IP Routing
Hi everyone,Regarding activating IP Routing on a l3 Switch I am a bit puzzled about how that would work.Let's say we have a 24 ports switch on which we have sdm prefer and IP Routing commands applied.If we no switchport port 0-11, while keeping ports...
Hello everyone,I am encountering an issue with my ASA 5515X running ASA Version 9.1(2) where traffic from devices in VLAN 99 cannot communicate with an external network (specifically 10.0.0.0/8).Here is an overview of my network configuration:ASA Con...
Resolved! L2 connection over L3, L2TP or VXLAN?
Hi,I just thought that between VXLAN and L2TP are same to send Layer 2 transport over L3. What is the major different for these both solution beside the function (L2TP are VPN terms and VXLAN are switching terms)?Glad to hear your response!
