Most of the document I have read all talking about using MPLS/VPN/BGP as a solution for enterprise network connection across the internet. Can MPLS be used without intergation with VPN and BGP? Thanks
Most of the document I have read all talking about using MPLS/VPN/BGP as a solution for enterprise network connection across the internet. Can MPLS be used without intergation with VPN and BGP? Thanks
I´m having problems with ARP traffic. Is possible limit this traffic on a router´s interface with the following command:router (config)#access-list nn permitrouter(config-if)#rate-limit .....How Can I limit this traffic ?regards.
Does anybody happen to know if Cat-6500 stores the system message logs in its NVRAM?Thanks.
Hi Group!I would like to know what is the impact of the configuration of the Cable Lenght on a T3+ PA interface.I mean what happens if the real cable lenght is longer than the configured cable lenght.And How the router react to this configuration.Tha...
Is there a way where you can set up a DFM email notifier when a switch shuts down or reboot. Preferably when it reboots..
hiWhat is the use of CVS and how to integrate with ciscoThanksSat
HII have found that on a 3662 with 3 NM-16 modem banks that at random the router resets the line config ( I think ) to its default values and they are shown in the running config. This happens to three of the modem banks the other one does not have a...
Hi I need to know if theres a way for me to mesures the bandwidth usage from the Router (1720 Ver 12.0[7]T). I have a T-1 line and need to know how hard my bandwidth is being hit.Thank you for your Time & Help!Josh
Hi AllI have a problemWe have a 192.168.1.0 network running as a class C. I want 192.168.1.1 as a gateway and 192.168.1.2 as a gateway.I want machines who come to the 192.168.1.1 gateway to go out of one of our internet connections via ISP1.I want ma...
I use a router ADSL 827 with IOS 12.2(15)T8. The network comprises an interface Ethernet 0 inside (IP 10.134.74.1) and one interface outside of the type Dialer 1 (dynamic IP ). I use a static route to communicate with my server since Internet ip nat ...
I will be upgrading a 6509 (SUP1a/MSFC2) from 6.3.6 to 8.2.1 in order to support a new 10/100/1000 copper blade. I went through the dynamic configurator to get the proper code version. The configurtor also recommended 24Meg flash card so I have that...
how do we rectify errordisable problem..sometimes i just need to shutdown the port and enable it again..but the worst thing is sometimes doing same thing is not rectifying the problem and requires rebooting the switch.pls advise.
Network Info:1) One Cisco router running BGP.2) Connected with two backbone providers. (A and B)3) /21 IP block from APNIC.Requirements:1) Some IP classes to use A as primary link and others to use B as primary link.2) In case of failure of any one l...
Hi,What's the advantage and disadvantage when we announce with BGP4 two subnets or the summarize of them?for example :- scenario 1 router bgp xxxxxnetwork 64.110.252.0 mask 255.255.252.0.......- scenario 2router bgp xxxxxnetwork 64.110.252.0 mask 255...
Hi I have a 64 kbps lease line connection to one of my offices and using a 800 series router.Along with this i do have a satelite connection to the same site.IS it possible to have a load balancing and a disaster recovery solution by utilizing the s...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |