Hi I need to know if theres a way for me to mesures the bandwidth usage from the Router (1720 Ver 12.0[7]T). I have a T-1 line and need to know how hard my bandwidth is being hit.Thank you for your Time & Help!Josh
Hi AllI have a problemWe have a 192.168.1.0 network running as a class C. I want 192.168.1.1 as a gateway and 192.168.1.2 as a gateway.I want machines who come to the 192.168.1.1 gateway to go out of one of our internet connections via ISP1.I want ma...
I use a router ADSL 827 with IOS 12.2(15)T8. The network comprises an interface Ethernet 0 inside (IP 10.134.74.1) and one interface outside of the type Dialer 1 (dynamic IP ). I use a static route to communicate with my server since Internet ip nat ...
I will be upgrading a 6509 (SUP1a/MSFC2) from 6.3.6 to 8.2.1 in order to support a new 10/100/1000 copper blade. I went through the dynamic configurator to get the proper code version. The configurtor also recommended 24Meg flash card so I have that...
how do we rectify errordisable problem..sometimes i just need to shutdown the port and enable it again..but the worst thing is sometimes doing same thing is not rectifying the problem and requires rebooting the switch.pls advise.
Network Info:1) One Cisco router running BGP.2) Connected with two backbone providers. (A and B)3) /21 IP block from APNIC.Requirements:1) Some IP classes to use A as primary link and others to use B as primary link.2) In case of failure of any one l...
Hi,What's the advantage and disadvantage when we announce with BGP4 two subnets or the summarize of them?for example :- scenario 1 router bgp xxxxxnetwork 64.110.252.0 mask 255.255.252.0.......- scenario 2router bgp xxxxxnetwork 64.110.252.0 mask 255...
Hi I have a 64 kbps lease line connection to one of my offices and using a 800 series router.Along with this i do have a satelite connection to the same site.IS it possible to have a load balancing and a disaster recovery solution by utilizing the s...
I have been using my catalyst 2950 without configuring it. Recently, I had a routing problem which I posted on my previous message and I decided to configure vlans on my switch but when I logged on to the console it displays unrecognised character or...
I have a 2610 router Ethetnet 0/0 Console AUX W0 (serial 0/0)The W0 interface is connected to my catalyst switch using the suitable adapter.The pb is that the W0 interface does not lit and is alway down. Even when I do the no shutdown command on ...
Suppose a location has 500 access level switches say 6509s. And, it is required to upgrade the code on these switches. What is the best way to do this task? with minimum effort and time.TIA Shahbaz
If route target export 100:1 on one PE1 , must I config route target import 100:1 on PE2 to make them in one VPN and then the PE2 is able to receive the routes through BGP? Vice versa for the route target import value on PE1 has to same as route tar...
I seem to be having a problem with my ANI server not syncing with RME. I can go into the ANI server set up and click on the Diag and then click on Discovery Metrics and I have a total of 876 devices but then when I go to RME and look at my inventory...
*Mar 6 21:17:57.120: %CONTROLLER-2-FIRMWARE: Controller T1 0/0, firmware is not runningThis is the error i get I have 3 VWIC-2MFT-T1 cards in them the card in slot has no lights on it i have tried other cards with the same result. I have upgraded S...
I have a CAT-6500 with a 6348. Scenario: Ports 1-6 on VLAN100 Ports 7-12 on VLAN200 In MLS Card the virtual interface for VLAN100 I have a network in the 215.128.3.0 In MLS Card the virtual interface for VLAN200 I have a network 215.128.4.0 The probl...
