hello cisco ,
i want to update my router series 2600 xm from 12 to 15 version
what should i do to get the new version
and where the img source file,please ? :)
Hi everybody. I have some issue with cisco prime 2.2 I configured cisco switches for snmp v3 and add in cisco prime
I have see only reachability of devices. I need too see cpu utilization memory utilization, Interfaces traffics statics bandwidth, ...
Dear All,
I have recently installed the iso version of cisco prime infrastructure version 3.1
i earlier had cisco mars running and the iso was downloaded by the vendor authorize partner.
now everything is working fine but i need to license the produ...
Hi all,
I'm encountered a problem when monitoring cisco switches 3020 (for HP bladeserver). Their snmp agent gives wrong ports speed.
On switches:
#sh ver....
Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 24 WS-C...
Is there such a script.
I have tried:
for xx in `show int status | i notconn`
do
echo $xx
done
and got a list of the interfaces but with the interface line broken up by the spaces;
like so:
953Test#for xx in `show int status | i notconn`do..done>...
Hi guys.
Looking for some help please guys.
I bought three cisco 2621xm routers recently. One boots up fine, and the other two clear the bootstrap 12.2 (8r) and then present the error - Memory not detected. I have transferred the good working memory...
Hi,Wonder if anyone has encountered an asterisk (*) when you do a "show logging" command on the switch. e.g.*Jan 13 11:05:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/26, changed state to downPlease advise what does it mean?Thank...
I have configured all my dhcp, nat, and access lists but i cant figure out why i cannot connect to the cable modem to get internet. Below is my sh ip route and sh ip int brief.
Gateway of last resort is 192.168.0.1 to network 0.0.0.0
S* 0.0.0.0/0 [1/...
I have a cisco 3600 , and the switch is configureg with "The password-recovery mechanism is disabled.".
And when the switch is start to load the IOS , this message apear. "Password recovery *disabled* and got break character.. auto booting".
I just t...
Hello,
I would like to know if my Cisco 6506 is support with the VSS option ?
on the global i can see the command :
Cisco-6506(config)#switch virtual domain ? <1-255> Virtual switch domain number
but on the Ten interface i cant see the option to V...
Our Subscription said that our modem is in plug and play (static) - If I will connect modem connected directly to PC in DHCP mode, but no access to the internet (unidentified)But if the modem will connect to the router first going to Devices, there i...
hi would you please check this serials ?FDO1920F1VT FDO1920F1RW related cisco SWITCH WS-C3750X-12S-EFDO1644X067 FDO1624Z17Y related cisco SWITCH WS-C3750X-24S-EFCZ15337OTY OR FCZ153370TY related cisco3945/K9 original or fack ?are these oem...
Hi,our cisco routers 2801 are vulnerable to CSCtd75033. Current IOS version is 12.4(1c). Can you help me to find right IOS for upgrade?Devices have 128 MB DRAM and 64 MB Flash. From download center looks fine for me version 12.4(19a). Software checke...
Hello there,
I would greatly appreciate some assistance. I have installed a NM-ESW-16 in my 2811 router and it is coming up with:
Port adapter is disabled.
The device is showing a green power light and it gives a light on the ethernet port when som...
