Hi,I got a Cisco6513 with native mode IOS. However, the keepalive command cannot be set on VLAN or switchport interface (Ethernet). Is there any workaround to make the local interface down if the interface on remote site is down?Thanks,Walter
Hi,I got a Cisco6513 with native mode IOS. However, the keepalive command cannot be set on VLAN or switchport interface (Ethernet). Is there any workaround to make the local interface down if the interface on remote site is down?Thanks,Walter
Does anybody remember the command from 11.2 of the enterprise IOS that allowed you to do a layer 4 tcp trace. I believe it is not published and no longer supported.
I am having 6 2950T-48-SI switches. These switches have 2 1000BaseT ports instead of GBIC slots. Will I be able to stack them like other 2950s. If so , how?Regards,Tijo
Hello, how I can verify whether an ATM PVC on an LS1010 "dropped cells". I can do on the controller, but I did not found any possibility to verify it per PVC.Te command "sh atm vc int atm x/y/z [vpi] [vci] " show me the Tx an Rx Cells, but no dropped...
I have a T1 between remote sites that have two separate networks at each end of the T1. We do not want to co-mingle the networks for security reasons and have been suggested to use the 1721's.A vendor gave us a quote for 1721's,WIC-1DSU-T1's,WIC-1ENE...
Are there MIBs to collect the following output:?5 minute output rate 2000 bits/sec, 3 packets/secThis came from a 2900XL. I know I can collect octet outputs, errors, etc, etc.I would like to have an SNMP trap when packets/sec exceed x amount, within...
Hi every one ..I'm looking for a solution, that can make a graphical view of the status of our BGP sessions , If a BGP sessions changes status, I need the graphical view to change, so our NOC can see witch BGP peer is up / down ..Best RegardsPeter
I'm new to cisco and i have a router 2600 series which i want to use in my network. I will like to use the router as a dhcp server. I have othere servers which will be attached to it. this is how it looks in the attached diagram. Please could some...
I am trying to install the broadband access center for cable 2.5 version on a solaris 8 system and having problem during the installation.I have upgraded my system with the J2sdk patch cluster and my system is at level [Generic_108528-27]. Some of th...
I keep getting traps from two of my switches that indicate interface 1 or sc0 is down, but I cannot figure out why. The other local switches do not have this problem.
Does anyone know if the CISCO aironet 350 can bridge ethernet through its console port.?
I am having problems setting up a TFTP service on my router. When I type TFTP-Server it gives me a list of: Flash, Null, System, Xmodem, Ymodem, etc. I chose all of them at one time or another and it always gives me the error: cannot find"whatever" i...
About this conversation:"Etherchannel newbie Mar 14, 2003, 10:46am PST can etherchannel span 2 boxes? Can you have port gig0/1 on switch A and port gig0/1 on switch B belong to etherchannel 1 if A and B are connected and terminate at C. " About this ...
a cat4908-L3 connected to a cat2980G via G5484 and a pair of multimode Fiber. the cat4908g-L3 log errors about every 25s. Jan 21 14:30:54: %AAL5-3-RXERR: Flow Hdr: (10) input packet dropped because of CRC errors
I have dual 6509s with dual sup720s and am having trouble with HSRP. The configurations automaticaly sync so a different priority for HSRP cannot be given to the second MSFC. I did some research and used the Cisco approach of the "alt" command for t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |