HiWe have a catalyst 6509 switch with a Sup1 / MSFC / PFC card and planning to upgrade from Cat OS to IOS. We would like to know if we can upgrade the switch running the following configuration to IOS.Mod Slot Ports Module-Type Model ...
Is there anyway to disable Spanning-Tree on a single port within a VLAN ? Spanning-Tree cannot be disabled for entire vlan. The command "PortFast BPDU Filter" will filter the sending of BPDUs but it looks like it will disable the port if it recieve...
Hello All. I'm setting up a lab with the following applications, for training purposes:CEMF 3.2 and EMS for GSR 12000 v. 3.1.1 and 7600 routers v. 3.0)CNS C-Note (Notification Engine) v. 3.0CNS Performance Engine v. 2.0CNS Netflow Collection Engine v...
All:I completed a network cutover this weekend, but had an issue with one etherchannel. All of my etherchannels between my 4503 and 4506' worked fine - I only had a problem with my connection to my 4006. Is it possible to form an etherchannel between...
Hi,I'd like to know if the backup modem connection to the internet on 1711 routers can also be used to restablish ipsec tunnels to headquarters.Thanks in advance,chabral
This urgent request relates to a conversation in the WAN and LAN area about Blocking DHCP requests >> see link below.http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.eea77c0If anyone could h...
Everytime atm pvc went down, CBR interface got lost connection with PABX, but interface shows that everyting was ok while PABX detected AIS. What I have to do is shutdown/no shutdown then everyting is ok.Is anyone know about any bugs on Catalyst 8500...
How are lan edge view determined in campus manager, I have inherited a cw2k server with views already determined, how are the put into different networks, and what are disconnected devices and can these be added to a particular netview.
I'm interested to know in the following sh mac-address table outputs, why i got four (4) same mac address in a different vlans of my network, Anybody got an explanation? Thanks.Leoswitch34.1#sh mac-address-table address 00d0.005e.4bfc Mac Ad...
How should direct request to my internal VNC server(private IP) which hidden behind NAT of my router.Assume I'm using PPoE for connection to internet.I only have 1 global IP to my WAN port.PLs advise
I would like to know the syntax to configure a floating static route on a 2600 series router.I have an idea however would like this confirmedip route 10.0.0.0 255.0.0.0 192.168.30.250 10ip route 10.0.0.0 255.0.0.0 192.168.30.250 2010 and 20 being the...
HiI'm setting up CiscoWorks on a W2000 server. The accompanying documentation says I need JVM 5.1.3182 to run with IE 6 to ensure correct operability.I've got JVM 5.0.0.3805 running at present.Where can I get the upgrade for this ?I've tried a collec...
I have a remote site connected via frame-relay to our corporate office. It has been working fine for a few days but has gone down. On the remote side I get an "UP - UP" on the serial link, yet on the corporate side I get a "Down - Down". I have ve...
Hi,When entering any command on RSM "Catalyst 5509" [sh ip route, sh version, sh run, ...] it take about 15 seconds to get the results. Sh proc cpu, show the %CPU is 4%. IOS version: 12.0(21a)CatOS version: 5.5(13a)Any idea, why it take so long. Than...
I have been asked to clean up our SRB. Most of it has been removed off the network. When talking to people at the sites I cannot get a real good feeling if the segments that are defined with it require it.I do a sh source and get the followingThis TC...
