I have a 5002 with 2 175 watt power supplies and a Supervisor II G. Status lights are all green. There is no 4 port module installed in the Supervisor II G.Hyperterminal shows nothing when plugged in. There is absolutely nothing. I have tried jum...
I have a 5002 with 2 175 watt power supplies and a Supervisor II G. Status lights are all green. There is no 4 port module installed in the Supervisor II G.Hyperterminal shows nothing when plugged in. There is absolutely nothing. I have tried jum...
I am having trouble advertising a default route from an NSSA ASBR to the ABR, and then subsequently getting the NSSA ABR to propagate that default route to the OSPF domain. The NSSA is connect to area 0 w/ a virtual link. I have tried different ver...
Hello AllI have installed the integration Utility, from the 5th Edition CD, on NNM 6.41. On the following Directory /opt/CSCOpx/nmim/mibs there are a File AllCiscoMibs.my. Mi question is, is a newer version from this File available?Kind regardsBruno
Hello,we are using CW2000 LMS2.1Is it possible to apply the saved topology views, like display view to different users. Normaly each user must create its own map from the default and save. But how can I save one map and treat that to all user ?Thanks
I have the following lines configured on a 3745. I'm unable to get rid of them using the command "no line 97" in (config)# mode. I receive the error message: % Vty line 97 doesn't existCan anyone provide a solution?line 97 location Router A Console...
I have a multihomed connectivity to two ISPs.Traffic is flowing through both the links but I want to control the traffic coming into our router from the outside world from one ISP with higher prefernce as compared to other ISP link.For outbound traff...
Hello, Is it possible to have two IP address range with different mask on Router side (MSFC ) of 6509 (IOS (tm) MSFC2 Software (C6MSFC2-PSV-M), Version 12.1(11b)E4, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) . For example , Vlan10 with IP address 16...
I have a Cisco 805 connected via Adtran TSU Ace to a 128k frame relay circuit. With the circuit connected, the router is getting an Illegal read access: Memory Protection Violation error. I can connect the network to the loopback jack on the Adtran a...
Hello,I saw that CWSMS-2.0 : Service Management Solution 2.0 WIN/SOL; SLM & Collection Mgr is EOL. Does someone know what product took its place?Thanks
We are looking to add a DSL connection to the Internet. Does WIC-1SHDSL support SDSL, which is quoted by DSL.NET?How reliable is DSL.NET? Anybody has any experience with them?Thanks.daniel
Greetings,I'm looking at 802.1q Tunneling documents for the 6500. I have a few questions:1) All of the command references are for IOS. Does that imply hybrid configuration is not supported when doing 802.1q Tunneling?2) Does the customer switch nee...
Recently our Cat3550 got error saying CEF was disabled due to low memory condition.TAC diagnosed it was a hardware failure and hardware was replaced.After a while, new symptoms happened and reported MALLOCFAIL (Memory Fragmentation and No Alternate P...
I've got a 2621 that I need to have autoconfigure the IP address on one of it's interfaces using DHCP. When I put in the above command on one of the FastEthernet interfaces all that I get when I do 'show ip interface brief' is that the IP will be co...
See thread 'IPSEC ESP Bad Pad Length #2'I see VPN 3000 version 4 has a .zip of all messages.Event ID: IPSEC/18 Severity: 3 Event Text: IPSEC ESP bad pad length (%d) >= buffer length (%d) Explanation: An internal software error has occurred. Reco...
Hello all, I have a client who has a Cisco 2500 router with IOS version 11.2(11). I need to upgrade this router to a newer IOS, but the customer bought the router used and does not know if it has a SmartNet contract. It also appears that the Serial...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |