Other Network Architecture Subjects

Sep 18, 2003, 7:26pm PST With this command: ip nat inside source static network 192.168.100.0 255.255.255.0 203.145.145.145 Is it possible for me to NAT a whole subnet of 192.168.100.0 to the external static ip address of 203.145.145.145. Eg, if I ha...

The topo just like :internet---pix---c2621(NAT-gateway)---pcNow PC can access internet , How can I block it without modify C2621's config ?(Because I have no permission)Regards

I have a Sup1A with MSFC/PFC that I have converted from hybrid to native. The conversion process went flawlessly, but when I issued the final reload to have it boot the native image automatically, I now cannot get into the console port. I get no outp...

Hi,I want to make DLSw as unintersting traffic to trigger the ISDN dial.IS below alone is enough or any additions requiredaccess-list 101 deny tcp any eq 2065 anyaccess-list 101 deny tcp any eq any 2065access-list 101 permit any anyThanks,Martin

i have big problem with switch catalyst 4006 ....with ( ws-4013 supervisor -3 modules ws-x4148-rj)without any reasons when i put any of the modules in slot 2 or slot 3 or slot 5 they give faulty status!!!! when i put modules in slot 4 or slot 6...

All of a sudden 3745 stopped processing and showed these errors when consoled in. Its memory fragmentation. IOS 12.2(15)T2. Anyone aware of an exact bug here?%SYS-2-MALLOCFAIL: Memory allocation of 276 bytes failed from 0x6049FF30, alignment 32Pool: ...

I have a trunk configured between a cisco 3508 and a cisco 3750. I checked the fiber and it is OK. The configurations are below. I have taffic in one direction only. Am I missing a comand or is there a problem to have a trunk between the two devices?...

The 'partition flash' command is not valid on the 3725 IOS. Is there a new commnd or has this very usefill capability been retired?

We have a client who uses a Cisco 1721 Router for their internet access and runs Microsoft SBS 4.5 for their server. They want to use VPN to access their office but I understand the 1721 does not support VPN. Is their a way of configuring the router ...

Port Security command is not accepting/functioning in 6509 core Switch, error, this command cannot be run in high availability mode. Thw switch is having all the modules as redundant, (Switch 6509 with dual supervisor engines 2, dual MSFC2, PFC2, du...

Hello!I have a 2610 router with an e1 card model NM-1CE1U. I've connected a channelized E1 where I have 2 circuits of 128K configured and one of 512K to be connected soon, not yet. IOS: 12.3.1a IP onlyI'm running HDLC to connect through these circuit...

Cheers,a customer of ours asked to proposed them a solution that will support Distributed Architecture...I would appreciate if you could advice which is the recommended configuration (scenario) we have to propose.SCENARIO A===========CORE SWITCH CONF...

hi,I installed the ciscoWorks2000 NMS and when i was trying to display CiscoWorks2000 using Internet Explorer by typing http://<Ip_Address>:1741 but i cannot browse the software installed expl: Ciscoview 5.3...It says JavaScript and Java are enabled ...

Hi all,I'm looking for a way to limit traffic from special ports to spetial other ports.The scenario is that we have a file-server attached to a Gig-Port. There are other servers also connected to Gig-ports at the same Cat6500, which send data to tha...

I have received a quote for a new install of a Cisco IP phone system that includes redundant 6000 series switches. Is there any good reason for not sticking with 4500 series switches instead? The 6000 is quite a bit more expensive, and the 4500 I h...