Do anybody know an equiventent Radius feature to the tacacs sendpass/sendauth facility. I dont know how to have a remote site authenticate a central site that is radius controled without falling back to the local authentication.
Do anybody know an equiventent Radius feature to the tacacs sendpass/sendauth facility. I dont know how to have a remote site authenticate a central site that is radius controled without falling back to the local authentication.
Hi, on my Cat6k-MSFC I'm having trouble setting DHCP manual bindings:Router(config)#ip dhcp pool GuestRouter(dhcp-config)#host 172.16.69.2 % This command may not be used with network pools.Router(dhcp-config)#hardware-address 0800.3712.9d76 % This co...
i have a very simple hub and spoke frame network.On a 'remote' router i added:access-list 100 deny icmp any any ehcoand then on the subinterface that connects back the to hub (here at HQ) i putip access-group 100 outmy intention is to stop pings from...
himy router is 3700 and my IOS is 12.2(15)T2 I have problem with analog modem . it is speed 21.6k I want to make it up to 56k but When I connect a session to the modem the line !!?? "This command has no effect on this line; use modem AT commands inst...
Hi,I use a backup program (Veritas Backup Exec) on a server which backups other servers on other VLAN's. Backup Exec v9.0 uses Microsoft Windows Network to search for these servers. Sometimes I see the servers and sometimes not, which then aborts the...
Dear all,Can anybody tell me how you would configure 2 x 4507R switches, that are interconnected via the Supervisor engines (using GBEC) to route between networks that sit on a single VLAN ?I have been told that we would need to setup multiple VLAN's...
I have IOS image c1700-sv3y-mz.121-5.T10 and two VIC-2FXS in my 1750. If i issued command show voice port summary, i should see status of my voice ports, but it looks like there is no voice ports at all. Upon system boot it finds two VIC-2FXS like it...
I want to config a 2501(use the aux port to connect a MODEM) as the access server with radius server authen(I use the WIN2K's IAS as the radius server,I have added a client whose ip address is 192.168.1.102,and share key is "cisco123"),but I failed,w...
The output of the sho proc command shows two percent values for the five second interval (see below). All other time intervals show only one value. What does the x%/y% vales mean?Thanks,DiegoCPU utilization for five seconds: 15%/12%; one minute: 17...
Hi,If i am using 1-1 static NAT Translation and e0 is the outgoing interface. Is it required to enable "proxy-arp" on e0 interface ?Regards \\ Naman
I have a 2513 router running IOS 11.2. We have a DHCP server on the token ring side and have just added some worksations on to the ethernet side. I also have a IP FORWARD-PROTOCOL UDP 1604 and IP HELPER ADDRESS' for Citrix servers (and the DHCP SERVE...
Hello,I've read an article in Cisco's PACKET Magazine under "Tech Tips" on how to show the supported MIBS of router within the router itself.I wanted to know how to do this since I wanted to monitor the memory and temperature of my Cisco routers.Than...
Hello All,Scenario: I have two location connected on 2 Mb circuit. I also have 4-BRI(S/T) at both locations. I DON'T HAVE HUNT-GROUP NUMBER FACILITY AT EITHER END.Required:Can some one suggest me the BEST way I can configure these ISDN's to backup my...
HiCan anyone pls help me out in finding whts this stats shows ?is this an spoofin type of case or anythng related to that since the brdcast ip is 255.255.255.255 ??SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP PktsSe5/2 ...
I am looking for a detailed document on how to, successful implement more than one vtp domain on the Cisco switch network.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
12-30-2024 06:12 PM | ||
12-09-2024 05:41 PM | ||
11-14-2024 09:33 AM | ||
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM |
User | Count |
---|---|
7 | |
1 | |
1 | |
1 |