Good Day,Can someone please let me know if the Cisco 4006 switch supports dynamic ip routing (eg. RIP, OSPF or EIGRP) or not? I think it doesn't but just want to make sure, thanks.Fanny
Good Day,Can someone please let me know if the Cisco 4006 switch supports dynamic ip routing (eg. RIP, OSPF or EIGRP) or not? I think it doesn't but just want to make sure, thanks.Fanny
Hello all :-) Does anyone know if the 3550 switch supports in line power for instance with use of a wireless access point? I'm guessing that if it does support it I would need the EMI and not the SMI ? Anyway, any direction would be much appreciat...
I have no problem configuring a trunk link between a 3550 and 2950 switches, and propagating VTP information. However, when I attempt to configure a trunk link between a 3550 and a older 3500XL or 2900XL, I cannot bring the link up. I have checked ...
I have two routers connected via point to point DS1--both 2501's. I have connected a hub to each Ethernet Interface and a PC to the hub. For some reason I can't ping the LAN side of either router from the local PC. I have no idea as to why.Here ar...
Can someone please advise if it is possible to do the following. I have a Cisco router attached on one interface to a broadband connection that provides 32 public IP host addresses. On the local connection I want to offer a NAT service overloaded to ...
I have a request for setting up a redondant PIX management solution (2 servers) with High Availability. I was that I can use Windows clustering with CWVPN but it seems to be that it's not supported.Any idea ?
If the NPE-400 will pass 400Kpps in CEF switching mode what will it pass in Process Switching mode and what size are the packets at 400Kpps?
I have a catalyst switch with NAM in the 9'th module. Till yesterday I was able login though telnet and web interface.Recently we upgraded the the version of the cat switch and since then I can not log in either through the telnet or the web interfac...
I have two Cisco 2501's connected via point to point DS1. One either end the server connected to a hub can ping both the Ethernet and Serial interfaces on the local router. When I telnet in to the router on this end, I can ping the other router. H...
Hi, I have a 416 Load Director. I was wondering if this can be used for a SQL database?Can the 416 load direct any ports or is it only FTP, SMTP, DNS, Telnet, Web?Thanks
Therer are no Distribute-lists. See below 10.0.31.230. The Netowrk and areas are properly defined on the configuration.Any idea Please?? Thanks============asydr01#sh ip ospf data adv 10.0.31.230 OSPF Router with ID (10.99.0.1) (Process ID 10) ...
I'm relatively new to multicast and we have a problem at the moment involving an application (called 'Isis') which sends a multicast keepalive every 5 minutes.The disappointing thing about this fault is that it usually happens during the night, and 3...
Hi,I have a wide area point to point connection via frame relay. The interface on my backbone router is UP/UP. My frame relay PVC is also active. The Serial interface at the router at the other end is also UP / UP. But the Sub interface is Down/ Dow...
Hi,everybody knows that the segment max length for a 100BaseT connection is +/- 100 meters.Is this because of the risk of collisions due to the delay introduced by the copper cable? (Making it compulsory for half duplex connections) Does the length l...
I recently had a buffer failure in a newer 2924 switch which effected my trunking line to my router. This pointed out some possible areas for improvement with respect to my hsrp timers. I am trying to simulate the issue again for test purposes. My qu...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |