Could I be getting this error "vtp domain mismatch' because VTP info is being carried over DLSW and injected into a different vtp domain???Any trouble shooting tips would be appreciated.
Hi,I have a T1 leased line to a partner location. The leased line is terminated on a router outside my firewall. Now as a backup ican i configure an IPsec VPN to the same partner site and have a floating static route so that traffic gets routed via ...
Hi all,Somebody tell me that the switch port in access mode can not recognize the tag of 802.1q. If that is true, the access mode ports also can not recognize the bits of cos in 802.1q. In this points, if I want to config qos with cos in 3550, I must...
Has anybody actually seen one of these things yet? They're backordered everywhere. I've had an order in at CDW for months. Products & Services was no help at all except to say: "yea, we don't know why they're backordered...."Thanks,Rick
Hi guys.i have a senario where router A (RTR A) connected to router b through 4 serial links and ospf is enabled and cost is manually assigned 50.similarly RTR C and RTR D.RTR A and RTRC are connected through fast ethernet cost 50.in normal case RTR...
Hi!I would like to know if there is anyway a Cisco router can do some source routing. I've got several ATM links and I would like split their load acording to the source address. Is this possible? If it isn't, any suggestions?Thank's a lot!Jorge B.
Is it possible to make router resolve clients DNS queries using DNS server from "ip name-server" line? The only DNS server I have is ISP's one. I don't want to set on Win2K computers IP address of ISP's DNS server. I want to set there IP address of m...
Hi all,I refered to the manual and I am confused about several voice commands:1. num-exp (in config mode)2. prefix (in dial-peer mode)3. tech-prefix (in dial-peer mode)It seems that the commands all change the dialed number to another number before t...
Hello all,I need to disable spanning tree on a Cat 2948-GL3 switch. The IOS Version is 12.0(14)W5(20). I dont see any commands to do this. Can somebody help ?Regards,Michael Fuller
Hi, Please help me with the following:A Catalyst 5500 loses connectivity on a Gigabit port at exactly 10 min intervals. This Catalyst has been up and working with the same config for 2 years. The port disconnect would cause a spanning tree change whi...
Hi All,The random-detect command, for example:random-detect precedence 0 32 256 100 I had seen some manual but I still can not understand what the parameter above "32 256 1000" for, and how to calculate it. Can any body give me a hand? Thank You!Best...
at first ,i think could use network cmd ,but give it a second thought , i think BGP router uses the netwok cmd populate BGP routes to other BGP router,so cant use this cmd here so ,now i dont know how can i do it
Our office need to set up the network for remote dialup access. For some reason we can only use a E1 line to achive the remote access mission, The remote office use the analog line to dialin. Cause it need too much time toplace an order for the cisc...
Here is the output of a sh spantree active : Why there are two different cost of 19 and 100 ? I noticed that 100 is connected to 10 MB/ half duplex devices, where the 19 is connected to 100MB full duplex. Why ?Any input is highly appreciated ?Thanks...
Hi, i have a router Cisco 2621 with two fastethernet port. Some days a go syslog router show me:02-19-2003 09:03:21 Local7.Error XX.XX.XX.XX 14546: Feb 19 09:05:09.998 : %AMDP2_FE-3-RXOVERFLO: FastEthernet0/1 Rx FIFO Overflowxx.xx.xx.xx is ip direct...
